Maintenance And Cleaning - vidaXL 60798 Bedienungs- Und Sicherheitshinweise

water temperature. There are 4 temperature scales
(Natural temp-low temp- medium temp-high temp) Natural
temp: Stops heating.
6.3 Seat ring
• When water temperature is high, the water temp indicator
will start to flash; When the water temperature is
controlled, the temperature will be displayed.
• Press the "Seat Temp" button repeatedly to set temperature
or adjust seat temperature.
• There are 4 seat temp scales (Natural temp-low temp-
medium temp-high temp) Natural temperature stands for
unheated.
6.4 Shower
• Press the "Spray" button for the rear nozzle to stretch and
start to spray (Before and after, the nozzle self-cleanses).
• Press the "Bidet" button for the front nozzle to stretch and
start to spray. (Before and after, the nozzle self-cleanses).
• Press the "Massage" button for the rear nozzle to stretch
and spray. (Before and after, nozzle self-cleanses).
• Press the "Weak" "Strong" buttons for the rear nozzle to
stretch and spray. Press the "Stop" button to stop spraying.
• The system will automatically save the force scale used.
• Press the "Massage" button again to stop massaging.
6.5 Drying
• Press the "Drying" button start drying, hot wind to finish
drying.
• Drying will stop automatically in approximately 5 minutes
from start.
• Press the "Weak" "Strong" button to change temp. The
system will automatically memorize the temp scale used.
• There are 3 temperature scales, indicated by the LED's.
6.6 Power saving
• Press the "Energy Saver" button to turn on Power Saving
Mode.
• The power of the seat and the water heater is cut off and
the unit enters a power saving mode. The chip sets an
8-hour saving period. Please use this function when you are
out or in bed. At the state of power saving, the water temp/
seat temp is low, the temp will return to the original set
temp when someone is on the seat, and back to the state of
power saving when someone left the seat.
• The power saver indicator is on. The unit returns to the set
temp automatically.
approximately 2 - 3 minutes to get to temperature).
• Once seated the indicator lamps of the seat and warm
water will both flash and the current temperature indicator
lights are on when the temperature is under control.
58 | 60798
(The seat and water
6.7 Stop
• Press the "stop" button to finish any active function.
6.8 Power
• Press the "Power" button and the machine will turn on/ off.
6.9 Purify
• Once seated or when the user has left, the device will purify
the air and operate automatically. When active, the Purify
indicator LED will be on.
• When the user is on the seat for 1 minute, the air purifying
function will stop automatically.
• When the user is away from the seat for half minute, the air
purifying function will stop automatically.
6.10 Lighting
• Press the "LED Lighting" to toggle the lighting on and off.
• When the water level is low in the water reservoir, the
lighting lamps will flash automatically.

7 Maintenance and cleaning

6 Do not pour water or detergent on or around the main
unit, or the power plug, it can cause electric shock or fire due
to short circuit.
5 Note
• Please pay attention to wipe the dews off on the water
reservoir.
• Moisture is formed mostly in the rain season or during
winter with a heater. If the surrounding area is not dry it
could cause the floor to be damp along with musty walls.
Hence, mop regularly and keep the area ventilated.
7.1 Daily cleaning
• Wipe with a damp soft cloth to remove any excessive dirt.
7.1.1 Cleaning Nozzles
1. Put a wet cloth on the sensor and press "Spray" or "Bidet"
button the nozzle will extend out.
2. Clean the nozzle and pole with a toothbrush. (Press "Spray"
or "Bidet" and wait at least 2 mins. Then Nozzle will move
back automatically).
7.1.2 Clean seat cover
1. Remove the power plug from the electrical outlet before
cleaning.
2. Remove the seat cover: (1). Remove the left coupling
bearing (2).Remove the seat cover from the right bearing of
need the unit.
3. Wipe off the stains on the seat cover.
4. Install the lid back: (1).Insert the seat cover into the right
bearing of the product. (2).Insert the left coupling bearing.
5. Plug the power socket into the outlet.