BNI PNT-565-W01-K079 Netzwerkschnittstelle Benutzerhinweise zu dieser Anleitung Gültigkeit Verwendete Symbole und Konventionen Verwendete Fachbegriffe und Abkürzungen Abbildungen Basiswissen IO-Link Wireless Allgemein Protokoll Datentypen Master-ID IMA Time Zykluszeit SSlot und DSlot Block-Parametrierung Data Storage Systemintegration Konfiguration Modul einbinden Einstellungen der Profinet-Kommunikation 3.3.1 Gerätenamen und Profinet-Adresse einstellen...
Seite 6
BNI PNT-565-W01-K079 Netzwerkschnittstelle WebUI / Webinterface Allgemein Navigationsleiste Benutzerprofil 4.3.1 Information / Unterlagen 4.3.2 Sprachauswahl 4.3.3 Benutzerverwaltung (ADMIN) 4.3.4 Profil bearbeiten (EXPERTE/NUTZER) 4.3.5 An- und Abmeldung Startseite 4.4.1 Portübersicht / Konfiguration 4.4.2 LEDs Diagnose 4.5.1 Status 4.5.2 Aktivitätsprotokoll Einstellungen 4.6.1 Modul 4.6.2 Tracks...
BNI PNT-565-W01-K079 Netzwerkschnittstelle Basiswissen IO-Link Wireless Allgemein Für die Zuweisung der IO-Link-Wireless-Geräte an das entsprechende IO-Link-Wireless-Modul ist ein Pairing- IO-Link integriert konventionelle und intelligente Sensoren Service implementiert. Zusätzlich gibt es einen Scan-Ser- und Aktoren in Automatisierungssysteme und ist als vice, der nicht gekoppelte Wireless-Geräte anzeigen kann, Kommunikationsstandard unterhalb der klassischen die sich in Reichweite befinden.
BNI PNT-565-W01-K079 Netzwerkschnittstelle Basiswissen IO-Link Wireless (Fortsetzung) Protokoll IMA Time Bei der IO-Link-Kommunikation werden zyklisch fest Die IMA-Zeit (I-am-alive-Zeit) ist ein obligatorischer definierte Frames zwischen W-Modul und W-Gerät ausge- W-Parameter. Im Normalmodus steuern W-Modul und tauscht. In diesem Protokoll werden sowohl Prozess- als W-Gerät die Zeit zwischen zwei aufeinanderfolgenden...
BNI PNT-565-W01-K079 Netzwerkschnittstelle Basiswissen IO-Link Wireless (Fortsetzung) SSlot und DSlot Es gibt entweder Single-Slot-Geräte oder Double-Slot- Geräte. Der Master hat keinen Einfluss darauf, was das Gerät ermöglicht. Ein Single-Slot-Gerät hat 1 Byte Rohda- ten und ein Double-Slot-Gerät 14 Byte. Für die Übertragung längerer Nachrichten kann eine Segmentierung verwendet werden, wodurch sich die Latenzzeit mit der Anzahl der benötigten Segmente multi-...
BNI PNT-565-W01-K079 Netzwerkschnittstelle Systemintegration Konfiguration Modul einbinden Bei Profinet-Geräten wird ein Gerät als modulares System Das Modul kann über die Suche in dem Katalog gefunden abgebildet, das über mehrere Datenmodule verfügt. und per Drag-and-drop in den Profinet-Strang gezogen werden (siehe Bild 3-1).
BNI PNT-565-W01-K079 Netzwerkschnittstelle Systemintegration (Fortsetzung) Einstellungen der Profinet-Kommunikation 3.3.1 Gerätenamen und Profinet-Adresse einstellen Nach einem Klick auf das Modul im Profinet-Strang wer- den die Kommunikationsparameter des Moduls angezeigt. Hier wird die Konfiguration des Gerätenamens sowie der Profinet-Adresse (IP) vorgenommen. Bild 3-2:...
BNI PNT-565-W01-K079 Netzwerkschnittstelle Systemintegration (Fortsetzung) 3.3.2 Priorisierter Hochlauf (Fast Startup) Ist der priorisierte Hochlauf (Fast-Startup (FSU)) aktiviert, laufen die Module innerhalb einer Zeit von weniger als 350 Millisekunden an. Um die Funktion zu aktivieren, müssen Einstellungen in der Hardware-Konfiguration vorgenommen werden.
BNI PNT-565-W01-K079 Netzwerkschnittstelle Systemintegration (Fortsetzung) 3.3.3 Ansprechüberwachungszeit Die Ansprechüberwachungszeit berechnet sich aus der Aktualisierungszeit und dem Faktor Akzeptierte Aktualisie- rungszeit ohne IO-Daten. Die Aktualisierungszeit entspricht dem Takt, mit dem die Telegramme mit der Steuerung ausgetauscht werden. Sie beträgt per Default 2 ms.
BNI PNT-565-W01-K079 Netzwerkschnittstelle Systemintegration (Fortsetzung) 3.3.4 Gerätetausch ohne Wechselmedium Die Module unterstützen auch den einfachen Gerätetausch im laufenden Betrieb über das LLDP (Link Layer Discovery Protocol). Gerätetausch ohne Wechselmedium aktivieren ► In der Hardware-Konfiguration der CPU das Kontroll- kästchen g erätetauSch Ohne...
BNI PNT-565-W01-K079 Netzwerkschnittstelle Systemintegration (Fortsetzung) Hardware-Konfiguration Die weiteren Module können bei Bedarf aus dem Hard- warekatalog per Drag-and-drop in die Konfigurationsta- belle gezogen werden und müssen passend zur Konfigura- tion des Kopfmoduls konfiguriert werden. Module adressieren Nach einem Doppelklick auf die Module kann die Adressie- rung im Fenster a geändert werden.
BNI PNT-565-W01-K079 Netzwerkschnittstelle Systemintegration (Fortsetzung) Geräteverbindung aufbauen ► In der g einen Rechtsklick auf das Modul eräteüberSicht ausführen und g wählen. erätename zuWeiSen Bild 3-9: Gerätebeziehung aufbauen Die Identifizierung findet über die MAC-Adresse oder über den Blinktest statt. Bild 3-10: Profinet-Gerätename vergeben www.balluff.com...
BNI PNT-565-W01-K079 Netzwerkschnittstelle Systemintegration (Fortsetzung) Gerätename vergeben IO-Link-Wireless-Kommunikation Zur Rückmeldung einer aufgebauten IO-Link-Wireless- ► Den gewünschten Gerätenamen vergeben und mit Kommunikation dient der Bitstatus. Er zeigt für jeden Hilfe von n dem markierten, gefundenen ame zuWeiSen IO-Link Wireless Port (5 × 8 = 40 Ports), ob eine Kommu- Gerät zuweisen.
Systemintegration (Fortsetzung) Funktionsbaustein CAP Value: Der CAP-Wert wird vom Hersteller vergeben. Bei Balluff Produkten ist es der Wert 0xFF (255). Um ISDU-Daten angeschlossener IO-Link-Geräte im Read/Write: Hier wird der Befehl definiert. Um Daten zu laufenden Betrieb schreiben oder auslesen zu können, lesen, muss hier eine 0, um Daten zu schreiben, eine 1 bieten die gängigen Programmieroberflächen der Steue-...
Seite 20
BNI PNT-565-W01-K079 Netzwerkschnittstelle Systemintegration (Fortsetzung) Der Funktionsbaustein IOL_Call baut ein Telegramm Schreiben zusammen, das über azyklische Dienste an das Modul Um Daten schreiben zu können, muss dem Modul eine übertragen wird. Folgende Einstellungen sind hierfür Schreibaufgabe für den entsprechenden Slot/Index/ notwendig: Subindex übermittelt werden.
Tool PRONETA von Siemens verwendet werden. Browser Das Webinterface ist kompatibel mit neueren Versionen von Google Chrome, Firefox oder MS Edge. Nähere Versionsinformationen siehe Datenblatt unter www.balluff.com auf der Produktseite. Bild 4-2: Benutzermenü (nicht angemeldet) Verbindungsaufbau In angemeldetem Zustand wird für Benutzer mit der Rolle admin zusätzlich die Benutzerverwaltung sichtbar (siehe...
BNI PNT-565-W01-K079 Netzwerkschnittstelle WebUI / Webinterface (Fortsetzung) 4.3.1 Information / Unterlagen 4.3.3 Benutzerverwaltung (ADMIN) Mit Klick auf i können gerätespezifische Informationen Mit b öffnet sich eine Ansicht der gespei- enutzerVerWaltung und Unterlagen eingesehen werden. cherten Benutzer. Es werden Informationen zum Status der...
BNI PNT-565-W01-K079 Netzwerkschnittstelle WebUI / Webinterface (Fortsetzung) 4.3.4 Profil bearbeiten (EXPERTE/NUTZER) Anmelden 1. a (siehe Bild 4-2 auf Seite 19) öffnet den nmelden Benutzer mit der Rolle eXperte oder nutzer können ihr Anmeldedialog (siehe Bild 4-11). Profil über p einsehen und ggf. ändern.
BNI PNT-565-W01-K079 Netzwerkschnittstelle WebUI / Webinterface (Fortsetzung) Startseite Bild 4-13: WebUI – Startseite (oben) Die Startseite (siehe Bild 4-13) zeigt wesentliche Informati- onen über das BNI-Modul selbst und dessen Netzwerkak- tivität. Es wird auch angezeigt, ob die Konfigurationssperre über die Steuereinheit (SPS) aktiviert wurde.
Seite 25
BNI PNT-565-W01-K079 Netzwerkschnittstelle WebUI / Webinterface (Fortsetzung) Bild 4-15: IO-Link-Port in der Breadcrumb wählen ► Alternativ den Zielport über die Breadcrumb-Navigation in der Kopfzeile wählen. Bild 4-16: IO-Link-Port in der Breadcrumb-Navigation wählen www.balluff.com deutsch...
Seite 26
BNI PNT-565-W01-K079 Netzwerkschnittstelle WebUI / Webinterface (Fortsetzung) Portdialog Bild 4-17: Portdialog Prozessdaten Mit Klicken auf das Erweitern-Symbol einer geschlos- Unter p werden nur dann interpretierte Daten senen Karte können z. B. Informationen zu relevanten rOzeSSdaten angezeigt, wenn eine passende IODD hinterlegt ist.
Seite 27
BNI PNT-565-W01-K079 Netzwerkschnittstelle WebUI / Webinterface (Fortsetzung) Parameter (IODD) Die Anzahl der IODDs, die hochgeladen werden können, ist durch den Speicherplatz auf dem BNI-Modul begrenzt. Die Karte Parameter (ISDU) wird nur dann ange- zeigt, wenn eine, zum am selektierten Port ange- schlossenen Gerät, passende IODD hochgeladen...
BNI PNT-565-W01-K079 Netzwerkschnittstelle WebUI / Webinterface (Fortsetzung) 4.4.2 LEDs Über die LEDs des BNI-Moduls werden Informationen über die aktuellen Prozessdaten und den Status des BNI- Moduls dargestellt. Die Bedeutungen der LEDs können in einer Legende eingesehen werden. LED-Legende aufrufen ► Auf led-legende klicken.
BNI PNT-565-W01-K079 Netzwerkschnittstelle WebUI / Webinterface (Fortsetzung) Diagnose Über die Navigationsleiste gelangt man mit Klick auf das entsprechende Icon (siehe Kapitel 4.2 auf Seite 19) zum -Dialog. Der d -Dialog bietet allgemeine iagnOSe iagnOSe Service-Informationen über das Gerät und eine Logging- Funktion.
BNI PNT-565-W01-K079 Netzwerkschnittstelle WebUI / Webinterface (Fortsetzung) 4.5.2 Aktivitätsprotokoll Das a stellt aufgetretene Ereignisse in ktiVitätSprOtOkOll ihrer zeitlichen Abhängigkeit dar. Damit ist es ein wichtiges Werkzeug zur detaillierten Störungssuche in Anlagen. Die aufgeklappte Karte a liefert eine ktiVitätSprOtOkOll tabellarische Darstellung der Log-Informationen, die nach Nummern sortiert werden können.
BNI PNT-565-W01-K079 Netzwerkschnittstelle WebUI / Webinterface (Fortsetzung) Einstellungen Mit neuStart wird das Modul neu gestartet (wie ein Ab- und Anschalten der Versorgungsspannung). Der Dialog e ermöglicht die Konfiguration von inStellungen Mit WerkSeinStellung Setzen wird die im Gerät angeschlossenen BNI-Modulen und Geräten. Über die hinterlegte Konfiguration vollständig gelöscht und anschlie-...
BNI PNT-565-W01-K079 Netzwerkschnittstelle WebUI / Webinterface (Fortsetzung) Tab. 4-2 zeigt die WLAN-Kanäle im 2,4-GHz-Frequenz- 4.6.2 Tracks band und dient als Hilfestellung beim Blacklisting. Im Dialog t können die 5 Tracks des Moduls konfigu- rackS riert werden. Kanal Mittenfrequenz [MHz] Bandbreite [MHz] 2412 2401…2423...
BNI PNT-565-W01-K079 Netzwerkschnittstelle WebUI / Webinterface (Fortsetzung) 4.6.3 W-Ports Beim Scannen detektierte Geräte können direkt durch Klick auf pairing gekoppelt werden. Um vor dem Kop- Im Dialog W-p können die einzelnen W-Ports konfigu- OrtS peln Port-spezifische Einstellungen vorzunehmen, kann riert werden. Zudem wird das Koppeln mit den einzelnen durch Klick auf kOnfigurieren die Portkonfiguration Geräten durchgeführt.
Seite 34
BNI PNT-565-W01-K079 Netzwerkschnittstelle WebUI / Webinterface (Fortsetzung) Portkonfiguration Über Scannen kann man nach Geräten suchen, die der Konfiguration entsprechen. In der Portkonfiguration kann der Port entsprechend des anzuschließenden Geräts konfiguriert werden. : Hier werden grundlegenden Einstellungen efault ettingS vorgenommen, um das BNI-Modul mit dem Gerät verbin- den zu können.
Seite 35
BNI PNT-565-W01-K079 Netzwerkschnittstelle WebUI / Webinterface (Fortsetzung) Angeschlossene Geräte Über pd können die Prozessdaten des Out Seg length Geräts im Downlink so segmentiert werden, dass andere Mit einem Klick auf einen belegten Port (siehe Geräte im selben Downlink ebenfalls die Möglichkeit Bild 4-32 auf Seite 31) öffnet sich erneut das Dialog-...
BNI PNT-565-W01-K079 Netzwerkschnittstelle WebUI / Webinterface (Fortsetzung) Diagramme zur Verbindungsqualität Unter dem Reiter d besteht die Möglichkeit, die iagramme Link Qualität des BNI-Moduls und dem Gerät eines ausge- wählten Ports anzuzeigen. Des Weiteren kann der RSSI Wert des Geräts zu einem Port ausgegeben werden.
BNI PNT-565-W01-K079 Netzwerkschnittstelle WebUI / Webinterface (Fortsetzung) IODD Über den iOdd-Dialog können Gerätebeschreibungsda- teien für IO-Link-Geräte (IODDs) und die zugehörigen Gerätebilder auf das BNI-Modul hochgeladen werden, damit im p -Dialog eine detailliertere Darstellung der OrtS angeschlossenen Geräte möglich ist. Verbundene Geräte Bei angeschlossenen Geräten und aktivierten Ports zeigt...
Seite 38
BNI PNT-565-W01-K079 Netzwerkschnittstelle WebUI / Webinterface (Fortsetzung) Über den zwischen den beiden Karten befindliche Dialog iOdd , kann eine IODD hochgela- Ochladen auSWählen den werden. Die Anzahl der IODDs, die hochgeladen werden können, ist durch den Speicherplatz auf dem BNI-Modul begrenzt.
BNI PNT-565-W01-K079 Netzwerkschnittstelle WebUI / Webinterface (Fortsetzung) Firmware Mit dem Aktualisierungs-Button kann entweder für jede Konfiguration einzeln geprüft werden, ob diese aktiv ist Unter f kann eingesehen werden, welche Version irmWare oder neben Status automatisch alle nacheinander. Dies der Firmware genutzt wird und wann diese hochgeladen dauert dann je nach Anzahl an vorhandenen Konfiguratio- wurde.
Dieses Token kann nun im Folgenden für die Durchführung REST APIs: von POST-Methoden genutzt werden. Dafür kann eine – Generische REST API für Balluff-Geräte und Applikati- entsprechende Anfrage mit dem Header Authoriza- onen. Basispfad der REST API im BNI-Modul: tion: Bearer 7euh07tdfawjej ausgestattet wer- http://[ip-address]/api/balluff/v1/ den.
BNI PNT-565-W01-K079 Netzwerkschnittstelle WebUI / Webinterface (Fortsetzung) 4.12.3 Abfrage von Port-Informationen 4.12.5 Setzen eines IO-Link-Geräteparameters (applicationSpecificTag) Alle relevanten Konfigurations- und Statusdaten für alle IO-Ports eines BNI-Moduls können abgefragt werden über: Die Verwendung einer POST-Anfrage setzt einen http://[ip-address]/api/balluff/v1/ports/information Login (siehe Kapitel 4.12.1 auf Seite 38) voraus.
BNI PNT-565-W01-K079 Netzwerkschnittstelle Diagnose Diagnosemeldung Block Header Die Diagnosemeldung, die das BNI-Modul bei einem Fehler Der erste Teil der Diagnose ist der sogenannte Block generiert, wird i. d. R. von der SPS ausgelesen und verar- Header, der 24 Byte lang ist. beitet. Genauso ist es möglich, die Diagnose mittels...
Seite 43
BNI PNT-565-W01-K079 Netzwerkschnittstelle Diagnose (Fortsetzung) Subslot Mögliche Werte Bedeutung 2 Byte Daten; Subslot beschreibt welcher Subslot des 0x33 IOL_E/A_32_32 Byte Steckplatzes einen Fehler meldet. 0x21 IO-Link-Kommunikationsstatus Subslots starten immer bei 1. Tab. 5-7: Module Ident Mögliche Werte Bedeutung Submodule Ident 0x0001 Subslot 1 4 Byte Daten;...
BNI PNT-565-W01-K079 Netzwerkschnittstelle Diagnose (Fortsetzung) Alarm Specifier Channel Number 2 Byte Daten; Alarm Specifier unterteilt sich wie folgt: Konfiguration als IO-Link Sequence Number Error Type Channel Number Bit 0…10 mit jeder neuen Diagnosemeldung wird dieser Line break Zähler inkrementiert. IOL Device wrong configuration Channel Diagnostic Tab.
Seite 45
BNI PNT-565-W01-K079 Netzwerkschnittstelle Diagnose (Fortsetzung) Direction Bit 13…15, Bedeutung mögliche Werte 0x00 Herstellerspezifisch 0x01 Kanal als Eingang verwendet 0x02 Kanal als Ausgang verwendet 0x03 Kanal als Ein- sowie Ausgang verwendet Tab. 5-18: Direction Channel Error Type Fehlercode Beschreibung 0x0000 Unbekannter Fehler 0x0001...
Seite 47
BNI PNT-565-W01-K079 Configuration Guide english...
Seite 49
BNI PNT-565-W01-K079 Network interface User instructions for this guide Validity Symbols and conventions Technical terms and abbreviations used Pictures IO-Link Wireless Basic Knowledge General Protocol Data types Master ID IMA Time Cycle Time SSlot and DSlot Block Parameterization Data Storage...
Seite 50
BNI PNT-565-W01-K079 Network interface WebUI/web interface General Navigation bar User profile 4.3.1 Information/documents 4.3.2 Language selection 4.3.3 User management (ADMIN) 4.3.4 Edit profile (EXPERT/USER) 4.3.5 Logging in and logging out Homepage 4.4.1 Port overview/configuration 4.4.2 LEDs Diagnosis 4.5.1 Status 4.5.2 Activity log Settings 4.6.1 Module...
BNI PNT-565-W01-K079 Network interface IO-Link Wireless Basic Knowledge General A pairing service is implemented for the assignment of the IO-Link Wireless devices to the corresponding IO-Link IO-Link integrates conventional and intelligent sensors and Wireless module. There is also a scan service which can actuators in automation systems and is intended as a display the unpaired wireless devices that are in range.
BNI PNT-565-W01-K079 Network interface IO-Link Wireless Basic Knowledge (continued) Protocol IMA Time With IO-Link communication, permanently defined frames The IMA time (I-am-alive time) is a mandatory W are cyclically exchanged between the W module and the parameter. In normal mode W module and W device W device.
BNI PNT-565-W01-K079 Network interface IO-Link Wireless Basic Knowledge (continued) SSlot and DSlot There are either single-slot devices or double-slot devices. The master has no influence on what the device allows. A single-slot device has 1 byte raw data and a double-slot device has 14 bytes.
BNI PNT-565-W01-K079 Network interface System integration Configuration Integrating a module For Profinet devices a device is created as a modular The module can be found in the catalog via the search system that has several data modules. function and pulled into the Profinet string via drag & drop (see Fig.
BNI PNT-565-W01-K079 Network interface System integration (continued) Settings of Profinet communication 3.3.1 Setting the device name and Profinet address After clicking on the module in the Profinet string, the communication parameters of the module are displayed. Here, the device name and the Profinet address (IP) are configured.
BNI PNT-565-W01-K079 Network interface System integration (continued) 3.3.2 Prioritized startup (fast startup) If fast startup (FSU) is activated, the modules start up within a time of less than 350 milliseconds. To activate the function, settings must be made in the hardware configuration.
BNI PNT-565-W01-K079 Network interface System integration (continued) 3.3.3 Watchdog time The watchdog time is calculated from the “Update time” and the Accepted update cycles without IO data factor. The update time corresponds to the cycle with which the telegrams are exchanged with the control. It is 2 ms by default.
BNI PNT-565-W01-K079 Network interface System integration (continued) 3.3.4 Device replacement without exchangeable medium The modules also support simple device replacement in LLDP mode (Link Layer Discovery Protocol). Activating device replacement without exchangeable medium ► In the CPU hardware configuration, activate the uppOrt device replacement withOut exchangeable medium checkbox.
BNI PNT-565-W01-K079 Network interface System integration (continued) Hardware configuration The remaining modules can, if necessary, be pulled into the configuration table from the hardware catalog using drag & drop and must be configured in accordance with the configuration of the headslot.
BNI PNT-565-W01-K079 Network interface System integration (continued) Establishing a device connection ► In the d , right-click on the module and evice Overview select a SSign device name Fig. 3-9: Establishing the device relationship The device is identified via the MAC address or the blink test.
BNI PNT-565-W01-K079 Network interface System integration (continued) Assigning the device name IO-Link Wireless communication The bit status serves for the feedback of established ► Assign the desired device name and assign it to the IO-Link Wireless communication. For each IO-Link...
Seite 63
System integration (continued) CAP Value: This is assigned by the manufacturer. For Balluff products, it is the value 0xFF (255). Read/Write: The command is defined here. To read data, it must be a 0; to write data, it must be a 1.
Seite 64
BNI PNT-565-W01-K079 Network interface System integration (continued) The IOL_Call function module composes a telegram that is Write transferred to the module via acyclic services. The To be able to write data, the module must be sent a write following settings are required for this: task for the corresponding slot/index/subindex.
User menu (not logged in) For more detailed version information, see the When logged in, users with the admin role can also see data sheet at www.balluff.com on the product the user management (see Fig. 4-3). page. Users with the expert or uSer role will see the entry e...
BNI PNT-565-W01-K079 Network interface WebUI/web interface (continued) 4.3.1 Information/documents 4.3.3 User management (ADMIN) Click on a to view device-specific information and Select u to open a view of the stored bOut anagement documents. users. Information on the user status (...
BNI PNT-565-W01-K079 Network interface WebUI/web interface (continued) 4.3.4 Edit profile (EXPERT/USER) Login 1. l (see Fig. 4-2 on page 19) opens the login Ogin Users with the expert or uSer role can view and, if dialog (see Fig. 4-11). relevant, change their profile via e .
BNI PNT-565-W01-K079 Network interface WebUI/web interface (continued) Homepage Fig. 4-13: WebUI – Homepage (top) The homepage (see Fig. 4-13) shows key information about the BNI module itself and its network activity. It also shows whether the configuration lock has been activated via the control unit (PLC).
Seite 69
BNI PNT-565-W01-K079 Network interface WebUI/web interface (continued) Fig. 4-15: Selecting the IO-Link port in the breadcrumb ► Alternatively, select the target port via the breadcrumb navigation in the header. Fig. 4-16: Selecting the IO-Link port in the breadcrumb navigation www.balluff.com...
Seite 70
BNI PNT-565-W01-K079 Network interface WebUI/web interface (continued) Ports dialog Fig. 4-17: Ports dialog Process data Click on the expand symbol of a closed tab page to Under p , interpreted data is only shown if a view e.g. information on relevant ISDU parameters.
Seite 71
BNI PNT-565-W01-K079 Network interface WebUI/web interface (continued) Parameter (IODD) The number of IODDs that can be uploaded is limited by the memory on the BNI module. The Parameter (ISDU) tab page is only displayed if a suitable IODD is uploaded for the device connected to the selected port.
BNI PNT-565-W01-K079 Network interface WebUI/web interface (continued) 4.4.2 LEDs The LEDs of the BNI module display information on the current process data and the status of the BNI module. The meanings of the LEDs can be viewed in a legend.
BNI PNT-565-W01-K079 Network interface WebUI/web interface (continued) Diagnosis Click on the corresponding icon in the navigation bar (see chapter 4.2 on page 19) to access the d dialog. iagnOSiS The d dialog provides general service information iagnOSiS about the device and a logging function.
BNI PNT-565-W01-K079 Network interface WebUI/web interface (continued) 4.5.2 Activity log The a displays events that have occurred in ctivity chronological order. It is therefore an important tool for detailed troubleshooting in systems. The expanded a tab page provides a table view ctivity of the log information, which can be sorted by numbers.
BNI PNT-565-W01-K079 Network interface WebUI/web interface (continued) Settings Master settings The S dialog enables the configuration of connected Basic settings can be made for the module under m ettingS aSter BNI modules and devices. Click on the corresponding icon in the navigation bar (see chapter 4.2 on page 19) to access the Settings dialog.
BNI PNT-565-W01-K079 Network interface WebUI/web interface (continued) Tab. 4-2 shows the WLAN channels in the 2.4 GHz 4.6.2 Tracks frequency band and serves as an aid in blacklisting. In the t dialog the 5 tracks of the module can be rackS configured.
BNI PNT-565-W01-K079 Network interface WebUI/web interface (continued) 4.6.3 W ports During scanning detected devices can be paired directly by clicking on pairing. In order to perform port-specific The individual W ports can be configured in the w-p OrtS settings before pairing, the port configuration can be dialog.
BNI PNT-565-W01-K079 Network interface WebUI/web interface (continued) Port configuration Via Scan a search can be carried out for devices which match the configuration. In the port configuration the port can be configured according to the device to be connected. : Basic settings are made here in order to...
Seite 79
BNI PNT-565-W01-K079 Network interface WebUI/web interface (continued) Connected devices Via pd the process data of the device can Out Seg length be segmented in the downlink so that other devices in the Click on an assigned port (see Fig. 4-32 auf Seite 31) to same downlink also have the option to transfer data.
BNI PNT-565-W01-K079 Network interface WebUI/web interface (continued) Diagrams for connection quality Under the d tab page there is the option to display iagramS the link quality of the BNI module and the device of a selected port. The RSSI value of the device for a port can also be displayed.
BNI PNT-565-W01-K079 Network interface WebUI/web interface (continued) IODD Via the iOdd dialog, device description files for IO-Link devices (IODDs) and the associated device images can be uploaded to the BNI module so that a more detailed illustration of the connected devices can be provided in the dialog.
Seite 82
BNI PNT-565-W01-K079 Network interface WebUI/web interface (continued) An IODD can be uploaded via the S iOdd elect fOr uplOad dialog between the two tab pages. The number of IODDs that can be uploaded is limited by the memory on the BNI module.
BNI PNT-565-W01-K079 Network interface WebUI/web interface (continued) Firmware With the Update button it can be checked whether each configuration is active separately or consecutively beside Under f you can see which version of the firmware irmware status. Depending on the number of configurations this is being used and when it was uploaded.
The present BNI module supports the following methods. A corresponding request can be equipped with REST APIs: the header Authorization: Bearer – Generic REST API for Balluff devices and applications. 7euh07tdfawjej. Base path of the REST API in the BNI module: http://[ip-address]/api/balluff/v1/ –...
BNI PNT-565-W01-K079 Network interface WebUI/web interface (continued) 4.12.3 Requesting port information 4.12.5 Setting an IO-Link device parameter (applicationSpecificTag) All relevant configuration and status data for all IO ports of a BNI module can be requested via: The use of a POST request requires login (see http://[ip-address]/api/balluff/v1/ports/information chapter 4.12.1 on page 38).
BNI PNT-565-W01-K079 Network interface Diagnosis Diagnosis message Block Header The diagnosis message that the BNI module generates in The first part of the diagnosis is the so-called Block the event of an error is usually read out from the PLC and Header, which is 24 bytes long.
Seite 87
BNI PNT-565-W01-K079 Network interface Diagnose (continued) Subslots always start at 1. Other values Meaning 0x21 IO-Link communication status Other values Meaning Tab. 5-7: Module ID 0x0001 Subslot 1 Submodule ID Tab. 5-6: Subslot 4 bytes of data; Submodule ID describes which...
Seite 88
BNI PNT-565-W01-K079 Network interface Diagnose (continued) Alarm Specifier Channel Number 2 bytes of data; Alarm Specifier divided as follows: Configuration as IO-Link Sequence Number Error Type Channel Number Bit 0…10 This counter is incremented with every new Line break diagnosis message.
Seite 89
BNI PNT-565-W01-K079 Network interface Diagnose (continued) Direction Bit 13…15, Meaning possible values 0x00 Manufacturer-specific 0x01 Channel used as input 0x02 Channel used as output 0x03 Channel used as input and output Tab. 5-18: Direction Channel Error Type Error code Description 0x0000...
Seite 90
Americas Service Center Asia Pacific Service Center Poland Greater China Balluff Sp. z o.o. Balluff Inc. Balluff Automation (Shanghai) Co., Ltd. Ul. Graniczna 21A 8125 Holton Drive No. 800 Chengshan Rd, 8F, Building A, 54-516 Wrocław Florence, KY 41042 Yunding International Commercial Plaza...