Werbung
Verfügbare Sprachen
Verfügbare Sprachen
18878 Sheet music and
document holder
- compatible with 18860 »Spider Pro« and 18840 »Baby-Spider Pro«
- closed steel desk: excellent desk pad and is magnetic
- can be placed anywhere on the support column,
-
variable adjustment of the angle
- W x H x D: 416 x 296 x 30 mm
Thank you for choosing this product. The instructions provide
directions to all of the important set up and handling steps. We
recommend you keep these instructions for future reference.
SAFETY NOTES
- Please consider the information provided in the setup instructions
- Please also consider the safety and the assembly instructions
-
for the »Spider Pro« Models 18840 and 18860
- It is not compatible with the 18850 Keyboard stand »Spider«
- Ensure that the screws are tight on all of the involved products
- Protect against moisture
-Please ensure that the music desk is properly assembled
-
and centered
COMPONENTS
The Sheet Music and Document Holder consists of three
COMPONENT GROUPS:
A. Music Desk: a Music desk, b slide bracket
B. Joint bracket: c Wing nut 3/8", d Receiver, e Knurled
screw M6, f Swivel bearing, g Wing nut M8
C. Slide:
h Haltewinkel, i Klammer
SETUP INSTRUCTIONS
INSTALLATION of the Slide to the »Spider-Pro«
1 Loosen the clamp i by the opening the lever
2 Place and hold the clamp to the Spider support column
3 Flip the lever all the way to affix the clamp onto the
3
support column
4 Should the clamp be too loose (or too tight) un-tighten the
4
lever and turn 180° clockwise. Then flip the lever to a
4
closed position. Repeat until the clamp is properly installed
4
on the stand tube.
INSTALLATION of the Music Desk
5 Unscrew the clamp screw (c) and use it to screw the joint f
5
to the bracket h.
6 Ensure that the threaded bolt of the knurled screw e does
6
not stick out.
7 Mount the music desk to the joint. Place the pin b as far
7
as it will go into the pin board d.
8 Tighten the knurled screw g which results in the music
8
desk j securely being in position The music desk can only
8
be removed if the screw is loosened.
USAGE NOTES
HEIGHT
19 Open the lever on the clamp i and...
10 ...position the loose clamp at the desired position on the
10
tube. Then flip the lever to a closed position.
ANGLE
11 Loosen the wing nut g and...
12 ...adjust the music desk angle and tighten the knurled nut.
DISTANCE and DIRECTION
13 Loosen the lower knurled screw c and adjust the note head
13
a. Tube distance (40 mm) - b. Direction (approx.160°)
MAINTENANCE, CLEANING
- in the event of workstation maintenance pay attention to
-
possible risks
- to care for the product use a damp cloth
FAULT-FINDING (F) and REPAIR (R)
F: Holder is unstable
F:
B: The original clamp setting is to wide (see 4)
F:
B: ATTENTION! Holder does not fit on the 18850 Keyboard
F: B: ATTENTION!
stand »Spider«
F: Music desk is not stable
F:
B: Re-tighten screws
TECHNICAL DATA
Clamp, Lever, Handle: PA, black
Bracket, Music Desk Steel, powder coating,
Material
black
Joint: Zinc - die-cast
Connecting Elements: Steel, galvanized
Dimensions Music Desk W x D x H 416 x 30 x 296 mm
Box
W x D x H: 480 x 320 x 70 mm
Weight
net: 2.1 kg, gross: 2.5 kg
KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
18878-000-55 Rev.02 03-80-277-00 09/15
All manuals and user guides at all-guides.com
COMPONENTS (packaging)
SETUP INSTRUCTIONS
INSTALLATION of the Slide to the »Spider-Pro«
INSTALLATION of the Music Desk
rubber washer
steel washer
VIEW
USAGE NOTES
HEIGHT
ANGLE
DISTANCE and
DIRECTION
Werbung
