All manuals and user guides at all-guides.com 1.6 Leistungsstufe tauschen 1.7 Lüfter tauschen 1.6.1 Demontage der Leistungsstufe 1.7.1 Demontage des Gerätelüfters • Deckel demontieren (siehe Punkt 1.2) • Deckel demontieren (siehe Punkt 1.2) • Steckanschluss J3 lösen • Schrauben des Gerätelüfterhalters lösen •...
All manuals and user guides at all-guides.com 1.8 Entstörfilter tauschen 1.9 Heizbuchse tauschen 1.8.1 Demontage Entstörfilter 1.9.1 Demontage Heizbuchse • Deckel demontieren. (siehe Punkt 1.2) • Deckel demontieren. (siehe Punkt 1.2) • Schrauben des Entstörfilters an der Geräteunterseite lösen. • Anschluss J1 von der Platine entlöten. •...
All manuals and user guides at all-guides.com 1.10 Transformator tauschen 1.11 Steuerplatine tauschen 1.10.1 Demontage Transformator • Flachbandkabel zwischen Steuerplatine und Hauptplatine an • Deckel demontieren. (siehe Punkt 1.2) Anschlüssen J1 der Steuerplatine und J7 der Hauptplatine • Leiterplatte demontieren (Punkt 1.5.1) vorsichtig trennen.
All manuals and user guides at all-guides.com 2. Inbetriebnahme Prüfplatine einstecken und Gerät einschalten. 2.3 Einstellung Trockenlaufschutz 2.3.1 Taster Nebel auf Maximal (Rechtsanschlag) stellen 2.1 Versorgungsspannungen messen. Spannung an Messpunkt MP 1 ( Masse) und MP 4 messen, mit Trimmer R23 Spannung auf ca. 3,0 V - 0,5 V einstellen. Wert in Masse für Messungen 2.1.1 bis 2.1.5 ist MP 1.
All manuals and user guides at all-guides.com 2.7 Inbetriebnahmeprotokoll USV UltraNeb Datum: Geräte Nr.: Platine Nr.: Hinweis! Spannungstoleranzen: Je nach Netzspannung oder Umgebungsbedingungen können die angegebenen Toleranzen über schrit- ten werden. Dies beeinträchtigt jedoch nicht die Funktion des Gerätes. Die angegebenen Spannungswerte dienen als Richtwerte um bei einer Fehlfunktion ein defektes Bauteil schneller analysieren zu können.
All manuals and user guides at all-guides.com 3. Fehlersuche 3.1 Fehlersuchtabelle Punkt Störung Abhilfe grün gelb Nach dem Einschalten kein Nebel in der Aus Aus Aus Netzzuführung, Netzschalter Netzsicherung auf der Verneblerkammer Rückseite überprüfen (T800L250) wie 3.1 Aus Aus Aus Gerät öffnen, Sicherung F2 (T250L250) überprüfen wie 3.1 Verneblerkammer oder Quarzmodul wechseln.
Seite 11
1.10.1 Removing transformer 1.10.2 Fitting transformer Change control board 1.11 Start-up instructions Measuring supply voltages Calibrating the power supply Setting dry-running protection Testing dry-running protection Testing electrical safety IEC 6011 Measuring points Test protocoll for UltraNeb UPS Trouble shooting Trouble shooting table...
All manuals and user guides at all-guides.com 1. Assembly instructions 1.1 Tools required 1.5 Changing PC board • Phillips screwdriver PH1, PH2 1.5.1 Removing PC board • 2.5 mm slotted screwdriver • Remove cover (see point 1.2) • 5.5 mm socket wrench •...
All manuals and user guides at all-guides.com 1.6 Changing power supply 1.7 Changing fan 1.6.1 Removing power supply 1.7.1 Removing device fan • Remove cover (see point 1.2) • Remove cover (see point 1.2) • Loosen plug connection J3 • Loosen screws on the device fan holder •...
All manuals and user guides at all-guides.com 1.8 Changing noise filter 1.9 Changing heating socket 1.8.1 Removing noise filter • Remove cover. (see point 1.2) 1.9.1 Removing heating socket • Loosen the noise filter screws underneath the device. • Remove cover. (see point 1.2) •...
All manuals and user guides at all-guides.com 1.10 Changing transformer 1.11 Change control board • Carefully separate ribbon cable between the control board 1.10.1 Removing transformer and the main board at connections J1 of the control board • Remove cover. (see point 1.2) and J7 of the main board.
All manuals and user guides at all-guides.com 2. Start-up instructions Insert test board and switch on device. 2.3 Setting dry-running protection 2.3.1 Set the vapour push button to the maximum setting 2.1 Measuring supply voltages (turning right till it stops) Measure voltage at measuring points MP 1 (earth) and MP 4, Earth for measurements for 2.1.1 to 2.1.5 is MP 1.
All manuals and user guides at all-guides.com 2.7 Test protocoll for UltraNeb UPS Date: Device no.: Board no.: Note ! Voltage tolerance: Depending on the mains voltage or environmental conditions the stated tolerances may be exceeded. This does not however affect the functioning of the device. The specified voltage values serve as a guideline in order to be able to quickly analyse defective parts in the case of an operating failure.
All manuals and user guides at all-guides.com 3. Trouble shooting 3.1 Trouble shooting table Symptoms LED indications Action Green Yellow No mist produced Check Power leads, Main switch and fuse on the rear (T800L250) No mist produced Open device and check fuse F2 (T250L250) No mist produced / fuse F2 checked Change chamber or transducer, then turn on device again...
Seite 19
Réglage de la protection pour la marche à sec Test de la protection pour la marche à sec Test de sécurité électrique IEC 6011 Points de réglage Mise en route du protocole du système d’alimentation sans coupure UltraNeb Localisation de disfonctionnement Table de localisation de disfonctionnement...
All manuals and user guides at all-guides.com 1. Instructions de montage 1.1 Outils nécessaires 1.5 Remplacement de la carte de CI • Tournevis cruciforme (Phillips) PH1, PH2 1.5.1 Démontage de la carte de circuit imprimé • Tournevis pour écrous à fente de 2,5 millimètres •...
All manuals and user guides at all-guides.com 1.6 Remplacement du bloc d’alimentation 1.7 Remplacement du ventilateur 1.6.1 Démontage du bloc d’alimentation 1.7.1 Démontage du dispositif de ventilation • Enlevez le couvercle (voir le point 1.2) • Enlevez le couvercle (voir le point 1.2) •...
All manuals and user guides at all-guides.com 1.8 Remplacement du filtre à bruit 1.9 Remplacement du manchon de chauffage 1.8.1 Démontage du filtre à bruit 1.9.1 Démontage du manchon de chauffage. • Enlevez le couvercle (voir le point 1.2) • Enlevez le couvercle (voir le point 1.2) •...
All manuals and user guides at all-guides.com 1.10 Remplacement du transformateur 1.11 Remplacement du tableau de commande 1.10.1 Démontage du transformateur • Séparez délicatement le câble-ruban entre le tableau de • Enlevez le couvercle (voir le point 1.2) commande et le panneau principal aux raccordements J1 du •...
All manuals and user guides at all-guides.com 2. Instructions de mise en marche Insérez le panneau test et allumez le dispositif. 2.3 Protection pour la marche à sec 2.3.1 Placez le bouton poussoir pour la vapeur au maximum 2.1 Réglage des tensions d’alimentation (en tournant à...
All manuals and user guides at all-guides.com 2.7 Protocole initial du système d’alimentation sans coupure de l’UltraNeb Date: Dispositif numéro: Panneau numéro: Remarque ! Tolérances de tension : en fonction de la tension secteur ou des conditions ambiantes, les tolérances indiquées peuvent être dépassées.
Seite 26
All manuals and user guides at all-guides.com 3. Dépannage 3.1 Table de dépannage Symptômes Indicateur à DEL Action Rouge Verte Jaune Pas de génération de vapeur Eteinte Eteinte Eteinte Contrôler les fils d’alimentation, commu - tateur principal et le fusible à l’arrière (T800L250) Pas de génération de vapeur Eteinte Eteinte Eteinte...
Seite 27
All manuals and user guides at all-guides.com...
Seite 28
All manuals and user guides at all-guides.com DeVilbiss Healthcare GmbH DeVilbiss Healthcare Ltd. DeVilbiss Healthcare S.A.S. Kamenzer Straße 3 Unit 3, Bloomfield Park, Bloomfield Road 13 - 17 Rue Joseph Priestley 68309 Mannheim Tipton, West Midlands DY4 9AP 37100 Tours...