EBECO Cable Kit 200 Montageanleitung Seite 13

Specifications Specifications
Cable Kit Cable Kit Cableflex
500 200 11
E 89 610 80 E 89 608 38 E 89 601 02
E 89 610 81 E 89 608 50 E 89 601 04
E 89 610 82 E 89 608 51 E 89 601 06
E 89 610 83 E 89 608 52 E 89 601 08
E 89 610 84 E 89 608 53 E 89 601 10
E 89 610 85 E 89 608 54 E 89 601 12
E 89 610 86 E 89 608 55 E 89 601 14
E 89 610 87 E 89 608 56 E 89 601 16
E 89 610 88 E 89 608 57 E 89 601 18
E 89 610 89 E 89 608 58 E 89 601 20
E 89 610 90 E 89 608 59 E 89 601 22
E 89 610 91 E 89 608 60 E 89 601 24
E 89 610 92 E 89 608 61 E 89 601 26
E 89 610 93 E 89 608 62 E 89 601 28
E 89 610 94 E 89 608 63 E 89 601 30 2080 W
Supplementary kit without thermostat for Cable Kit 500/200:
E 89 608 90
*Tolerance -5 % - +10 %
Materials and accessories
Included in package:
Underfloor heating cable (2.5 m connection cable) X
Thermostat with sensor cable
Spiral tube with adapter
Adhesive sticks
Reel bracket
Sign Heating Cable Installed
Accessories
Cable Clip (E 89 609 58)
Cable Board (E 89 601 80)
Tape (E 89 353 49)
Sensor hose (E 89 605 41)
Adhesive sticks (E 16 939 93)
Compare with the contents in your kit. Check the label on
the cable reel to ensure that you have received the correct
cable length.
Plan the installation
Because the heating cable may neither be cut nor crossed,
installation must be carefully planned so that the cable is
correct for the room. Use the metre marking on the cable
after half the installation to make any adjustments to c/c
distances and to avoid surplus heating cable once the
calculated area has been covered.
Calculate the c/c distance
Do as follows to find the exact c/c distance for cable
laying. Calculate the room's floor area. Subtract for fixed
furnishings, such as cabinets and counters, so that you
obtain the free floor area. Divide the free floor area by the
Output Length Nominal
specified
heating output
100 W 8.9 m 0.1 kW
150 W 13.5 m 0.15 kW
200 W 18.5 m 0.2 kW
260 W 23 m 0.26 kW
330 W 31 m 0.33 kW
400 W 37 m 0.4 kW
470 W 43 m 0.47 kW
540 W 49 m 0.49 kW
650 W 58 m 0.65 kW
810 W 73 m 0.81 kW
960 W 86 m 0.96 kW
1180 W 107 m 1.18 kW
1380 W 124 m 1.38 kW
1710 W 155 m 1.71 kW
187 m 2.08 kW
1180 W 107 m 1.18 kW
CK 500 CK 200 Cableflex 11
X
X X
X X
X X
X X
X X
Max cont. AREA AREA
heat 75 W/m² 110 W/m²
output
0.1 kW 1.1 m² 0.8 m²
0.15 kW 2.0 m² 1.35 m²
0.2 kW 2.7 m² 1.85 m
0.26 kW 3.4 m² 2.3 m²
0.33 kW 4.4 m² 3.1 m²
0.4 kW 5.3 m² 3.7 m²
0.47 kW 6.3 m² 4.3 m²
0.49 kW 7.2 m² 4.9 m²
0.65 kW 8.7 m² 5.8 m²
0.81 kW 10.7 m² 7.3 m²
0.96 kW 12.8 m² 8.6 m²
1.18 kW 16.05 m² 10.7 m²
1.38 kW 18.3 m² 12.4 m²
1.71 kW 22.7 m² 15.5 m²
2.08 kW 27.7 m² 18.7 m²
1.18 kW 16.05 m² 10.7 m²
X
Heating cable
X
X
Existing floors (chipboard, plasterboard
or concrete) with Cable Board/Thermo
Board insulation board, if any.
On EPS concrete/cement, reinforcement
mesh is required. When laying on rein-
forcement mesh, the cable must be laid
on the top of the reinforcement mesh.
Also see the applicable industry regulations for wet rooms.
Installation in wooden subfloors; see page 6.
free floor space (m²)
c/c distance (m) =
cable length (m)
cable length to obtain the c/c distance. Depending on the
c/c distance, output varies per square metre. In the table,
Specifications, you can see the output for various c/c
distances.
Only on concrete
subflooring
AREA AREA Resist-
ance*
140 W/m² 160 W/m²
0.6 m² 0.5 m² 534 Ω
1.1 m² 0.9 m² 350 Ω
1.5 m² 1.3 m² 260 Ω
1.8 m² 1.6 m² 207 Ω
2.3 m² 2.1 m² 161 Ω
2.8 m² 2.5 m² 133 Ω
3.4 m² 3.0 m² 112 Ω
3.9 m² 3.4 m² 98 Ω
4.7 m² 4.1 m² 81 Ω
5.8 m² 5.0 m² 66 Ω
6.9 m² 6.0 m² 55 Ω
8.4 m² 7.4 m² 45 Ω
9.8 m² 8.6 m² 38 Ω
12.2 m² 10.7 m² 31 Ω
14.9 m² 13.0 m² 25 Ω
8.4 m² 7.4 m² 45 Ω
Tiles, linoleum
Screed/Fix
Primer
x 100
EN
13