Warranty Terms - ARESA AR-1804 Bedienungsanleitung

ENGLISH
• Do not use the device with damaged blades - this can result in injury.
• Unplug the appliance if it is not in use, and before cleaning.
• Be extremely careful when children or disabled persons are near the appliance.
• Do not use outdoors.
ATTENTION: REGULARLY LUBRICATE THE BLADES.
• Do not use the hair-clippperfor inflammation of the skin.
• Do not shear animals.
• The manufacturer reserves the right, without additional notice, to make minor changes in the design of the product that do not radically affect its safety, performance
and functionality.
• Keep this instruction manual.
ATTENTION! Do not use the appliance near water in bathrooms, showers, swimming pools, etc.
OPERATION
LEVELING OF THE BLADE
Before shipping the units from the factory, the cutting blades of the clipper were adjusted and lubricated. In case of replacement or cleaning, the blades must
be adjusted again. The tooth profiles of both blades must match exactly during installation, regardless of their displacement.
The ends of the teeth of the removable (external) blade should be extended approximately 1.2 mm above the ends of the movable (internal) teeth, as shown in the photo.
If the blades are not installed correctly, apply a few drops of oil on them, turn on the hair clipper for a few seconds, then turn it off and unplug it.
Slightly loosen the two screws and reinstall the removable blade. Tighten the screws.
LUBRICATION
To maintain the unit in a good condition, you should lubricate the blades regularly. Do not use vegetable oil or oil that includes solvents.
Solvents are subjected to evaporation, and the remaining thick oil can slow down the upper blade moving speed. To lubricate the blades, use
the special oil for hair clipper blades.
LEVER OF THE BLADE
The lever , that moves the lower blade, is located under the thumb (if you are right-handed). When cutting hair you can move the blade, pressing
the lever, thus adjusting the cutting length without usage of the attachment combs. In the upper lever position, haircut will be the shortest one. In the
down lever position the cutting length is approximately the same as with the 3 mm attachment comb usage. Changing the position of the lever while
cutting hair, you can select the necessary length of the hair to cut.
If hair is jammed in the blades while cutting, move the lever from the upper position to the down position several times, so you can release the jammed hair without removing
the blades.
When the hair clipper is switched on, move the lever several times from the upper position to the lower position, this way you can remove the cut-off hair from the blades.
If the unit pulls hair while cutting, it means that the blades became blunt, replace them with new ones.
INSTRUCTIONS FOR HAIR CUTTING
Hair should be clean and dry while cutting.
• Insert the power plug into the mains socket.
• Before cutting hair, switch the unit on by moving the power switch to the position and make sure that the hair clipper operates normally and the blades move smoothly.
If there is excess oil on the blades, remove it with a dry cloth.
• Constantly check the power cord, prevent it from multiple twisting, regularly switch the unit off and straighten the power cord.
• Seat the person so that his/her head is approximately at your eye level, cover the person's shoulders with a towel and set
hair with the comb. To see the techniques of the cutting, refer to the photos.
BEGINNING OF THE CUTTING
Hair cutting requires practice. It is always better to leave the hair longer for the first few haircuts, until you get used to
the length of the head which cuts your hair.
DETACHABLE HEADS
The hair clipper head №1 leaves a 3-millimeter length of hair.
The hair clipper head № 2 leaves 6 mm of hair length.
The hair clipper head № 3 leaves a 9-millimeter length of hair.
The hair clipper head № 4 leaves a 12-millimeter length of hair.
Set the attachment upper part on the blade and press it until click. To remove the attachment comb, press the clamp and
remove the attachment.
TRANSPORTANTION, CLEANING AND STORAGE
TRANSPORTATION. Transportation of the device is necessary by any kind of covered transport with the application of cargo securing rules
ensuring preservation of the presentation of the product and / or packaging and its further safe operation. DO NOT expose the device to shock
loads during handling operations.
CLEANING. ATTENTION! Never wash parts of the appliance in the dishwasher. Do not use chemicals or abrasives.
Always unplug the appliance before cleaning.
• The clipper should be cleaned and lubricated after each use.
• Clean the motor with a soft cloth. Do not wash the hair clipper under the stream of water and do not immerse in water or other liquids.
• Use a brush to clean the unit and the attachments. Apply 1-2 drops of lubricating oil to the unit's blades.
• Ensure that the appliance and all its accessories are clean before storing it. • To avoid damaging the cord, do not wind it on the body. • It is
allowed to hang the hair-clipper by a special loop.
STORAGE. The device must be stored indoors, in conditions that presume the preservation of the presentation of the product and its further safe
operation. To avoid damaging the cord, do not wind it on the body.

WARRANTY TERMS

When purchasing the product, ask for it to be checked in your presence. Without the having a warranty card or when it is not properly filled in,
the quality claims are not accepted, and no warranty repair is performed. The warranty card should be presented at any address to the service
center during the whole warranty period. The product is accepted for service in a complete set only. The warranty period is calculated from the
moment of sale to the buyer. Keep the documents confirming the date of purchase of the product (cash receipt).
The condition of free warranty service of your product is its correct operation, which does not go beyond personal domestic needs, in accordance
with the requirements of the operating instructions for the product, the absence of mechanical damages and the consequences of careless
handling of the product.
The product is accepted for warranty service in its pure form. The warranty covers all manufacturing and construction defects (except those
listed in the "Warranty does not apply" section), identified during the warranty period. During this period defective parts, except consumables,
are subject to free replacement in the warranty service center.