MLINE ALPHA Bedienungsanleitung

Manual
ALPHA
Bluetooth Headset
multifunction
button
microphone charging socket
volume (+)
volume (-)
indicator light
receiver
1. Charging Your Bluetooth ® Headset
1.1. Before you use the headset for the first
time, please charge the battery fully (appro-
ximately 2 hours are required) with the
enclosed USB cable to a computer or USB port
of a charger.
1.2. The indicator light turns red while char-
ging, and will automatically turn blue after the
battery is fully charged.
1.3. When the headset is running out of bat-
tery, the indicator light will flash red.
Note: If left unused, a fully charged headset
will lose its power automatically. It is recom-
mended to charge the headset every month.
Do not place or keep the headset in extreme
conditions which may affect the headset's ope-
rations. The optimal temperature is between
15° C and 25° C. Do not attempt to force open
the built-in battery as this can damage the
headset.
2. Turning on/off the headset
2.1. Turning on: Press and hold the multifunc-
tion button for about 3 seconds until the light
flashes green.
2.2. Turning off: Press and hold the multifun-
ction button for about 6 seconds until the
indicator light is off.
Status announcement
a. When the headset is on/off, the automatic
voice prompt will tell you: power on/off
b. You will be informed when the headset is
connected/disconnected.
c. The automatic voice prompt will tell you
when the battery is low.
3. Pairing your headset with a Bluetooth
phone
3.1. Ensure the Bluetooth of your device is
switched on and the headset is switched off.
(The distance between your phone and head-
set shall be within 1 metre.)
3.2. Toggle the on/off button, the green light
will flash 3 times to enter into pairing mode.
3.4. Search Bluetooth devices (see the user
guide of your phone for instructions) and
select headset "ALPHA" from the found
devices list of the phone.
3.5. Enter the password „0000", confirm to
pair the headset with your phone. (If the pai-
ring cannot be completed successfully, please
repeat the above mentioned steps to try the
pairing again. Some phones pair without any
password).
3.6. When the headset is off, it will connect
with the paired phone automatically if you
turn on the headset again.
4. Answering a call
When you receive an incoming call, shortly
press the MFB or answer the call with your
phone.
5. Ending a call
You can end the call by shortly pressing the
MFB. or end the call with your phone.
6. Reject a call
You can either press the end key on your pho-
ne or press the MFB for 2 seconds.
7. Making a call – manual dialing
Dial the number on your phone's keypad and
press the call key.
8. Making a call – Voice dialing
In Standby mode, press the MFB for two
seconds. Say the voice tag as soon as you hear
the short beep. (Ensure your phone supports
voice dialing function, and you have recorded
the voice tag in your phone. See the user
guide of your phone for instructions.)
9. Last number dialing
When the headset is connected to the phone,
press the MFB twice. It will call the last
number automatically.
Note: If the headset is connected in multipoint
mode, it will call the number from the phone
which was first paired or re-connected.
10. Playing Music
You can play the music directly from your mo-
bile phone, tablet, computer etc. When you
are listening to the music, you can press Play,
Previous Song, Next Song (refer to the but-
ton's feature) to select your optimal perfor-
mance. For next song press volume (+) button
for 3 seconds. To go back to the previous song
please press volume (-) button for 3 seconds.
Volume control
In order to increase the volume please shortly
press the volume (+) button. To lower the
volume shortly press volume (-) button.
11. Disconnecting
To disconnect the paired headset from your
phone, please turn off the headset or dis-
connect the headset from the Bluetooth
menu of your phone.
12. Multi-point function
This Bluetooth headset allows you to connect
two 2 Bluetooth phones to the headset at the
same time. When neither phone A nor phone
B are paired, the multi-point operation is as
follows:
12.1. Pair the headset with your phone accor-
ding to chapter 3. „Pairing your headset with a
Bluetooth phone".
12.2. Turn off the headset and turn off the
Bluetooth function on your phone. Turn the
headset on again.
12.3. Repeat the steps from chapter 3. „Pai-
ring your headset with a Bluetooth phone"
with your phone B. If the multi-point operati-
on is already activated, This is how to use it:
Activate the Bluetooth function of phone
A and phone B. Turn on the headset, it will
automatically re-connect with both phones
within minutes.
13. Automatic re-connection
If you turn the headset on and it is already
paired with one phone, it will connect auto-
matically with your phone. If it happens that
the automatic re-connection does not work,
please connect it manually.
14. Reset
If the headset does not respond even if the
battery is full, please press the MFB. After
the reset and the restart the headset can be
used as usual.
15. The Headset Charging Notice
When the headset is charging, the indicator
light is red, while it is blue when the charging
is completed. If the indicator light does not
react, please check the following: Please ensu-
re that the USB output is 5V.
16. Safety and general information
16.1. Please read this guidebook carefully.
16.2. Use only supplied and approved USB
cable or another MLINE cable.
16.3. Please keep the headset away from hu-
midity, liquid, fire, sharp objects and extreme
temperature.
16.4. Protect the headset against dust and
dirt.
16.5. Do not clean the headset with strong
Detergents, chemicals or solvents.
16.6. Do not attempt to open the device.
Bluetooth Specification V 4.0
Transmission Power Class 2
Operation Range Up to 10 Meters
Battery Built-in Rechargeable
Li-polymer Battery
DC Output: 5V 150mAh
Charging Time about 2 hours
Talk Time* up to 8 hours
Standby Time * up to 150 hours
Weight About 11 g
*The time mentioned as above may vary
due to user's operation mode and device
settings.
CE Certification
This product is CE marked accor-
ding to the provision of the R&TTE
Directive (99/5/EC).
We declare that this product is in
compliance with the essential
requirements and other relevant
provisions of Directive 1999/5/EC.
For further information and the
complete declaration of conformi-
ty respectively, please go to www.
mline.com/download
Bluetooth® is a trademark owned
by the Bluetooth SIG, Inc.
For any further information, plea-
se feel free to visit www.mline.
com
Correct disposal of this product
(Waste Electrical & Electronic
Equipment) (Applicable in the Eu-
ropean Union and other European
countries with separate collection
systems).
This marking shown on the
product or its literature, indicates
that it should not be disposed with
other household wastes at the end
of its working life.
To prevent possible harm to the
environment or human health
from uncontrolled waste disposal,
please separate this from other
types of wastes and recycle it res-
ponsibly to promote the sustain-
able reuse of material resources.
Household users should contact
either the retailer where they
purchased this product or their
local government office, for details
of where and how they can take
this item for environmentally safe
recycling.
Business users should contact
their supplier and check the terms
and conditions of the purchase
contract. This product should not
be mixed with other commercial
wastes for disposal.
[IMPORTANT NOTE]
To comply with RF exposure
requirements, this device may
not be co-located with any other
transmitter or antenna.