Inhaltszusammenfassung für Gemü 1436 cPos DeviceNet
Seite 1
1436 cPos DeviceNet Intelligenter Stellungsregler und integrierter Prozessregler Intelligent Positioner and integrated Process Controller ORIGINAL BETRIEBSANLEITUNG OPERATING INSTRUCTIONS Status 05.2019 Stand 05.2019 / Ab Version 2.0.3.6 / From version 2.0.3.6 1436 cPos DeviceNet...
Nicht korrigierbarer Fehler (z. B. double MAC-ID) Rot / Grün blinkt Kommunikationsfehler M12-Stecker keine Funktion bei DeviceNet A-Kodierung Can H Can L 2.4 Elektrischer Anschluss Versorgungs- Versorgungs- spannung spannung 24 V DC 24V DC DeviceNet DeviceNet 1436 cPos DeviceNet 3 / 32...
Definiert die Byteanzahl, welche vom GEMÜ 1436 cPos an den DeviceNet-Master gesendet wird. 0 Byte 2 Byte 3 Byte 11 Byte (Einstellung für die Standard EDS-Datei) Baudrate Definiert die Baudrate der Feldbuskommunikation. 125 KBaud 250 KBaud 500 KBaud PwrOnT.Out Definiert die Zeit zwischen einer Fehlererkennung und Meldung beim Einschalten des Reglers. 1436 cPos DeviceNet 5 / 32...
Der erste Fehler wird mit der Nummer 0x00 0x01 angefordert. (Wegsensor) festgestellt. Antwort des GEMÜ 1436 cPos: 0xYY 0x44 („D“) Nummer Anzahl der Wert des aktiven Fehlers aktiven (über ID angewählt) aktiven Fehler Fehlers 1 Byte 1 Byte 2 Byte 4 Byte 1436 cPos DeviceNet 7 / 32...
Boost NO CtrlFn 0834 2100 Write Auto Auto NC Auto NO Auto DA Auto NC B Auto NO B adjtTimeClose 0835 2101 Read [0..999] *0,1s adjTimeOpen 0836 2102 Read [0..999] *0,1s *nur bei aktiviertem Prozessregler. 1436 cPos DeviceNet 11 / 32...
Seite 12
OFF/ON Save/ON In X 0CE5 3301 Write ParamSetB0 ParamSetB1 Poti/Ix OFF/ON Save/ON In 1 0CE6 3302 Write ParamSetB0 ParamSetB1 Poti/Ix OFF/ON Save/ON In 2 0CE7 3303 Write ParamSetB0 ParamSetB1 Poti/Ix *nur bei aktiviertem Prozessregler. 1436 cPos DeviceNet 12 / 32...
Seite 13
SSE max SSE min/max AlarmMinK2 0D4E 3406 Write [2..998] *0,1% AlarmMaxK2 0D4F 3407 Write [2..998] *0,1% SSE2Time 0D53 3411 Write [1..1000] *0,1s ErrorTime 0D50 3408 Write [2..1000] *0,1s Close ErrorAction 0D51 3409 Write Open Hold 1436 cPos DeviceNet 13 / 32...
Seite 14
Untermenü zur Einstellung der Feldbusverbindung 5 Communication DeviceNet Adr 1450 5100 Write [1..63] 0: 125 KBaud Baudrate 1453 5203 Write 1: 250 KBaud 2: 500 KBaud PwrOnT.Out 13ED 5101 Write 0...300 s *nur bei aktiviertem Prozessregler. 1436 cPos DeviceNet 14 / 32...
Seite 16
Trigger an action in the GEMÜ 1436 cPos 5.6.9 Quit field bus event 5.6.10 NoInit 5.6.11 Clear Error List 5.6.12 Set Default 5.6.13 Init Valve 5.6.14 goClose 5.6.15 GoOpen 5.6.16 Find Function 5.6.17 Adjust Time 5.6.18 Find Coefficient 5.6.19 Init Pilot Parameters table 1436 cPos DeviceNet 16 / 32...
Unrecoverable error (z. B. double MAC-ID) Red / Green flashing Communication error M12 plug No function at DeviceNet design A coded Can H 2.4 Electrical connection Can L Supply Versorgungs- voltage spannung 24 V DC 24V DC DeviceNet DeviceNet 1436 cPos DeviceNet 17 / 32...
Drop cable Drop cable Maximum cable length Drop cable Baudrate Maximum cable length per drop cable Maximum drop cable accumulated length 125 KBaud 156 m 250 KBaud 78 m 500 KBaud 39 m 1436 cPos DeviceNet 18 / 32...
DeviceNet ← GEMÜ 1436 cPos Defines the bytes to be sended from the GEMÜ 1436 cPos to the DeviceNet-Master. 0 Byte 2 Byte 3 Byte 11 Byte (standard setting for the EDS-file) Baudrate Defines the Baudrate of the communication. 125 KBaud 250 KBaud 500 KBaud PwrOnT.Out Defines the time between error recognition and reporting when the positioner is being switched on. 1436 cPos DeviceNet 19 / 32...
2 bytes 4 bytes sensor) was detected. The first error is requested with number 0x00 0x01. Response from the GEMÜ 1436 cPos: 0xYY 0x44 ("D") Number Amount Value of active error of active of active (selected via ID) error errors 1 byte 1 byte 2 bytes 4 bytes 1436 cPos DeviceNet 21 / 32...
2100 Write Auto Auto NC Auto NO Auto DA Auto NC B Auto NO B adjtTimeClose 0835 2101 Read [0..999] *0.1s adjTimeOpen 0836 2102 Read [0..999] *0.1s *Only if the process controller is activated. 1436 cPos DeviceNet 25 / 32...
Seite 26
In X 0CE5 3301 Write ParamSetB0 ParamSetB1 Poti/Ix OFF/ON Save/ON In 1 0CE6 3302 Write ParamSetB0 ParamSetB1 Poti/Ix OFF/ON Save/ON In 2 0CE6 3303 Write ParamSetB0 ParamSetB1 Poti/Ix *Only if the process controller is activated. 1436 cPos DeviceNet 26 / 32...
Seite 27
SSE max SSE min/max AlarmMinK2 0D4E 3406 Write [2..998] *0.1% AlarmMaxK2 0D4F 3407 Write [2..998] *0.1% SSE2Time 0D53 3411 Write [1..1000] *0.1s ErrorTime 0D50 3408 Write [2..1000] *0.1s Close ErrorAction 0D51 3409 Write Open Hold 1436 cPos DeviceNet 27 / 32...
Seite 28
Submenu for setting the fieldbus connection 5 Communication DeviceNet Adr 1450 5100 Write [1..63] 0: 125 KBaud Baudrate 1453 5203 Write 1: 250 KBaud 2: 500 KBaud PwrOnT.Out 13ED 5101 Write 0...300 s *Only if the process controller is activated. 1436 cPos DeviceNet 28 / 32...