Bedienungsanleitung
REG-Multifunktions-Jalousieaktor
4-Kanal
Bezeichnung
REG-Multifunktions-Jalousieaktor 4-Kanal, 4 verriegelte
Schliesskontakte 6 A potentialfrei, Versorgungsspannung 12
VDC
KURZ ANLEITUNG
Jalousieaktor gemäss Schema anschliessen
Drehschalter HEX auf 0 stellen
LRN 2 Sekunden drücken
Durch weiteres Drücken auf LRN den Kanal wählen. Die
Kanalnummer erscheint auf der 7-Segment-Anzeige SEG.
Hand- oder Wandsender in der Nähe des Schaltaktors
zweimal betätigen. CLR leuchtet während einer Sekunde,
danach ist der Sender eingelernt
Weitere Sender einlernen
Zum Beenden CLR drücken
FUNKTIONE N
Ansteuerung von 230 V~ Rohrmotoren in Jalousien,
Sonnenrollos, Markisen, Roll- oder Garagentoren
Lamellenpositionierung
Bedienung durch Hand- oder Wandsender
Fenster- und Schiebetürüberwachung
Innentemperatur gesteuerte Automatikfunktion mit Omnio
Raumfühler RTF
Automatikfunktion für Wind, Sonne und Regen im Zusam-
menspiel mit einer Omnio Wetterstation
Hand-Automatik Umschaltung mit Omnio Wandsender
oder Key-Card Schalter
Positionierfunktionen und Rückmeldungen für
übergeordnete Steuerungen und Visualisierungen
Repeaterfunktion
EnOcean Equipment Profile (EEP) D2-05-01
ARCO fähig (AWAG Remote Commissioning)
AL LGEM EIN
Die Omnio Aktoren (Empfänger) werden über Funksignale der Omnio Sender an-
gesteuert. Jeder Sender kann eine unbegrenzte Anzahl von Aktoren ansteuern.
Die Funksender werden manuell durch ein einfaches Verfahren auf den Aktor ein-
und ausgelernt. Jedem Sender können am Aktor eine Funktion und verschieden-
ste Parameter zugeordnet werden.
Mit ARCO-Technologie lassen sich alle Omnio Aktoren vollständig und ohne
manuellen Zugriff zum Gerät per Funk konfigurieren. Die leistungsstarke Software
E-Tool bildet dabei das Herzstück, um Projekte beliebiger Grösse bequem am
Schreibtisch zu planen, konfigurieren und dokumentieren.
PRODUKTBESCHREIBUNG
Der Omnio REG-Multifunktions-Jalousieaktor 4-Kanal REGJ12/04 ist ein Gerät
zum Ansteuern von 230 V~ Rohrmotoren in Jalousien, Sonnenrollos, Markisen
und Roll- oder Garagentoren. Seine vier potentialfreien, gegeneinander verriegel-
ten Ausgangspaare dienen zur Regelung von vier Antrieben und können von bis
zu 50 Omnio Funksendern angesteuert werden. Dies erlaubt die genaue
Positionierung von Jalousie und Lamellen. Weitere Merkmale sind Fenster- und
Schiebetürüberwachung, Innentemperatur gesteuerte Automatikfunktion, An-
schluss einer Omnio Wetterstation XFJ sowie Positionierfunktionen und Rück-
meldungen für übergeordnete Steuerungen oder Visualisierungen. Bidirektionale
Kommunikation, EEP D2-05-01, ARCO fähig (AWAG Remote Commissioning).
Geeignet als Reiheneinbaugerät für die Verteilermontage, Breite 4 TE.
ANZEIGE - UND BEDIENELEM ENTE
Klemmen
T1
Speisung (+) 12 VDC
T2
Speisung (-) GND
T3-5
Abschirmung
T6
RS485 GND
T7
RS485 Signal B
T8
RS485 Signal A
T9-11
Ausgang K1
T12-14 Ausgang K2
T15-17 Ausgang K3
T18-20 Ausgang K4
Bedienelemente
CLR
Taste und LED Clear
LRN
Taste und LED Learn
HEX
Drehschalter 0..9A..F
SEG
7-Segment Anzeige
Jumper
R
Abschlusswiderstand 120 Ω
AWAG Elektrotechnik AG Sandbüelstrasse 2 CH-8604 Volketswil
Tel. +41 44 908 19 19 Fax +41 44 908 19 99 info@awag.ch www.awag.ch
All manuals and user guides at all-guides.com
REGJ12/04M
Typ / Type
REGJ12/04M
T9
T10
T11
T12
T13
T14
T15
T16
T17
T18
T19
T20
Multi-functional DIN rail mounted
blind actuator, 4-channel
Art.-No./Item N°
Designation
Multi-functional DIN rail mounted blind actuator 4-channel,
4402 000
4 interlocked closing contacts 6 A potential free, supply voltage
12 VDC
BRIEF INSTRUCTION
Attach blind actuator according to schematic
Turn the rotary switch HEX to 0
Press LRN 2 seconds
Repress LRN to increment the channel number. The
channel appears on the 7-segment display SEG.
Press handheld of wall mounted transmitter twice and keep
it close to the actuator. CLR lights up for a second, after
that the transmitter is programmed
Program further transmitters
To finish press CLR
FUNCTIONS
Controls 230 V~ tubular motors of blinds, sun blinds,
awnings, sliding gates or garage doors
Slat angle settings
Controlled by handheld or wall mounted transmitters
Window and sliding door surveillance
Indoor temperature controlled automatic mode with Omnio
sensor RTF
Automatic mode for wind, sun and rain in conjunction with
an Omnio weather station
Manual/automatic change over with handheld or wall
mounted transmitter or key-card switch
Positioning functions and feedback for higher-level control
and visualisation
Repeater function
EnOcean Equipment Profile (EEP) D2-05-01
ARCO ready (AWAG Remote Commissioning)
GENER AL
The Omnio actuators (receivers) are controlled by radio signals coming from the
Omnio transmitters. Each transmitter is able to control an unlimited amount of
actuators. The radio transmitter can be manually programmed and deprogrammed
to an actuator following a simple procedure. Via actuator each transmitter can be
given a certain function and different parameters.
With ARCO technology, all Omnio actuators can be configured completely by
radio without manual access to the device. The powerful software E-Tool
constitutes the key component for conveniently planning, configuring and
documenting projects of any size right at your desk.
PRODUCT DESCRIPTIO N
The Omnio multi-functional DIN rail mounted blind actuator 4-channel REGJ12/04
is a device to control 230 V~ tubular motors of blinds, sun blinds, awnings, sliding
gates or garage doors. Its four pairs of potential free interlocked outputs are able
to regulate four drives and can be controlled by up to 50 Omnio radio transmitters.
This allows the exact positioning of blinds and slats. Further features are window
and sliding door surveillance, indoor temperature controlled automatic mode,
connection of an Omnio weather station XFJ, positioning functions and feedback
for higher-level control and visualisation. Bidirectional communication, EEP D2-
05-01. ARCO ready (AWAG Remote Commissioning). Suitable for DIN rail
mounting, width 4 TE.
DISPL AY AND OPER ATIN G ELEM ENTS
Terminals
T1
T1
T2
T2
T3-5
T6
T3-5
T7
T8
T6-8
T9-11
R
T12-14
CLR
T15-17
LRN
T18-20
HEX
Operating elements
SEG
CLR
LRN
HEX
SEG
Jumper
R
Manual
EnOcean-Technologie (868 MHz )
power supply (+) 12 VDC
power supply (-) GND
shield
RS485 GND
RS485 signal B
RS485 signal A
output K1
output K2
output K3
output K4
button and LED clear
button and LED learn
rotary switch 0..9A..F
7-segment display
terminal resistor 120 Ω
4404000.docx / 1876127
V01.001 / 30.08.2016 Seite 1 / 7