Dab Mode - Regent i351s Bedienungsanleitung

EN
BT Tx and DLNA
BT Tx (Bluetooth transmitter)
This internet radio offers you the option of wireless listening with Bluetooth
enabled headphones or TWS earbuds via the built-in Bluetooth transmitter.
1. Press the BT button on the remote control while listening to the media,
the display will show three options for BT Tx mode as follows:
• Enable (speaker on) - to enable the BT Tx function, and the sound
will still come from the radio speaker at the same time.
• On (speaker off) - to enable the BT Tx function and
turn off the sound from the radio speaker.
• Disable - to disable the BT Tx function.
2. Select one of the Enable options to enable BT Tx function, then turn on the
Bluetooth enabled headphones or TWS earbuds. It will take about 30 seconds
to search for and automatically connect the earphones or TWS earbuds. Once
connected, you can listen to the radio with headphones or earbuds.
Note: The range of the Bluetooth transmitter is limited to approx. 140 meters
(open area) depending on the surroundings and the device used.
DLNA
Besides UPnP, this device can also support DLNA function. Internet radio can
play a music stream from a DLNA-compatible device as long as the Internet
radio and other DLNA devices are on the same Wi-Fi network. The radio will be
detected as „Regent i351s" when you try to search for it on other devices.
Note: The DLNA function is compatible and works with the corresponding third
party applications on the Android platform. Apple devices are not supported.
FM mode
Extend the telescopic antenna and adjust its layout to optimize the reception level. Select
FM from the main menu to enter FM mode. To automatically scan the next/available
FM station, press and hold the PREVIOUS or NEXT button for 2 seconds, the radio will
automatically search for an available station. If you want to fine tune the frequency,
turn the UP/DOWN dial on the unit or press the ^/v buttons on the remote control.
Automatic scanning of presets
You can automatically preset FM stations. Press the UP/DOWN + OK dial (or the ^/v + OK
buttons on the remote control), you will be asked whether to perform auto scan or not. Select
"Yes" and press OK to confirm and the scanning and presetting of the stations will start.
When finished, short press the PRESET button, the first preset station will be displayed.
Station tracking
This is a feature that helps you find the same station on the Internet, provided the radio
station has an Internet stream available and is suitable for playing on the radio. Listening to
Internet radio allows you to free yourself from noise which is usually caused by interference
or poor FM reception. After scanning the FM band, select the channel to be played. If the
same channel is available on the Internet, an icon will appear in the lower right corner of
the screen. Press and hold the UP/DOWN + OK knob (or ^/v + OK buttons on the remote
control), the receiver will switch to internet radio mode to play the corresponding channel.

DAB mode

You can listen to regular DAB channels without internet connection. Extend the telescopic
antenna and adjust its layout to optimize the reception level. Select DAB from the main menu
to enter DAB mode. If you use DAB mode for the first time, the receiver will automatically scan
for DAB radio stations. After scanning, the receiver will display a list of found DAB stations.
Select the station you want to listen to and press the UP/DOWN + OK dial (or the ^/v
+ OK button on the remote control) to confirm playback. Press the PREVIOUS button
(or < on the remote control) to return to the station list. Pressing the PREVIOUS button
(or < on the remote control) again will display a warning that the station list is being
deleted. It also allows you to rescan DAB stations. Select <NO> to keep the existing
station list and search for new stations. Select <YES> to delete the existing station
list and perform a full scan again. Select <ESC> to exit the current operation.
To stop playing a station, press the PLAY/PAUSE button. Each time
you want to resume the game, press the same button again.
Configuration
Time display
You can choose to display the time in analogue or digital mode.
Network
Wireless network configuration
Press the UP/DOWN + OK dial (or ^/v + OK button on the remote
control) to scan for available wireless networks.
Wireless network (WPS PBC)
WPS allows the radio to connect to the router by pressing one key on the receiver and the
WPS key on the router for Wi-Fi connection, provided that the router has WPS function.
Manual configuration
You can enable or disable DHCP and enter the network name
(SSID) or delete the connected network (SSID).
Check network after turning on
Enable or disable checking and network connection when turning on the receiver.
Date and time
The time is automatically set and adapted to the geographic location of the
receiver. This setting allows you to manually modify the date and time.
Set the time format
Time format setting: 12/24 hours.
Set the date format
Date format: YYYY/MM/DD, DD/MM/YYYY and MM/DD/YYYY. If manual configuration
is selected, the Summer Time Setting (DST) option will also appear in the list.
EN