Werbung
Verfügbare Sprachen
Verfügbare Sprachen
PEHA Elektro GmbH & Co. KG
Postfach 1727 • D-58467 Lüdenscheid • Tel.: (02351)185-0 • Fax: (02351)27666 • e-mail: peha@peha.de • Internet: www.peha.de
mounting and installation
This device is intended for installation in a flush-mount installation box with 60 mm Ø.
They are to be equipped with the 1 - 5 multipurpose frame from the PEHA switch range.
a)
coding switch
The coding switch sets the module address. The setting is
presented in the PHC software under menu item
„Components Modules".
b)
bus connection (data connection)
notes:
– Usually, a JY(ST)Y 2x 2x 0,8 mm Ø connection
is used as a data cable.
– The module can be positioned anywhere in the data line.
The module is supplied with voltage by the bus line.
c)
Labelling area
engage labelling area
screw on mounting screws
note: PEHA labelling sheets (Art. No.: 75-17 Na) for the labelling area can be ordered
at PEHA. The template for the position of the labelling area (Avery-Zweckform) can
be found on our homepage (www.peha.de) under: Service Downloads PHC
House Control System
oPeraTIon anD FuncTIons
operation
operation
Press button T1 - T8
Press labelling area approx.
2 sec in the middle
notes:
– The functions of the input pushbutton for the PHC system are to be
programmed with the PHC system software (see PHC manual).
– Illumination and illumination menu are optional!
PEHA_M_940-8-4-2.xx ET(B) (Rev02_130306)
All manuals and user guides at all-guides.com
bus connection
(input connector)
0V -B +A +24V
Pin assignment
ON
coding switch
(module address)
1
2 3 4 5 6 7 8
connector assignment
24V
A
B
0V
Phc bus line
(connector included in delivery)
Insert labelling area into
plate and engage light
diffuser
Function
Switching PHC functions
(programming required)
Illumination menu ON / OFF
31060000-163
Illumination menu (optional)
Press labelling area for approximately 2 sec
Illumination menu on (all LEDs flash twice)
adjustment of
illumination intensity
Press labelling
area shortly
notes:
– Illumination and illumination menu are optional!
– After switching on the illumination menus, the feedback LEDs are swit-
ched off. After switching off the menu, the feedbacks are displayed again.
– The adjustment of the illumination intensity takes place in 7 dimm levels.
– Without further action, the illumination menu is turned off after 30 sec.
Phc soFTware
Programming
The functions of the input pushbutton for the PHC system are to be programmed with
the PHC system software (see PHC manual).
caution! For programming, the new setup version of the PHC software 2.6.2
is required! It is available on the Internet under: www.peha.de.
assignment of address area
LeD output
LeD
ET0.xx.00
L1
ET0.xx.01
L2
ET0.xx.02
L3
ET0.xx.03
L4
ET0.xx.04
L5
ET0.xx.05
L6
ET0.xx.06
L7
ET0.xx.07
L8
ET0.xx.08
L9
expansion of address area
A PHC control module can manage a maximum of 32 modules of one module type.
Through the expansion of the address area (ET0 ET1), the input pushbutton can be
assigned to either the module type of the input modules or the multi-function modules.
Therefore the DIP button 6 of the input pushbutton has to be switched on. Thus a
flexible use of the input pushbutton in the PHC system is possible.
ON
1
2 3 4 5 6 7 8
ET0.xx.00
ON
1
2 3 4 5 6 7 8
ET1.xx.00
TroubLeshooTIng & remeDIes (auThorIseD eLecTrIcIan)
new system or existing system
• Check circuit breaker and power supply
• Check connected electrical loads and connection cables
• Check module address (coding switch).
• Check PHC programming and transfer again.
contact
Telephone: .................. +49 (0)2351 185-0
Fax:............................. +49 (0)2351 27666
Internet: ...................... www.peha.de
E-mail: ........................ peha@peha.de
Press labelling area
for approx. 2 sec
Illumination menu oFF (all
LEDs flash 4 times)
Input
8-fold
4-fold
ET0.xx.00
T1
T1
ET0.xx.01
T2
−
ET0.xx.02
T3
T2
ET0.xx.03
T4
−
ET0.xx.04
T5
T3
ET0.xx.05
T6
−
ET0.xx.06
T7
T4
ET0.xx.07
T8
−
basic class ET0 (input modules)
module adress (ET0.00 - ET0.31)
input / output
basic class ET1 (multi-function modules)
module adress (ET1.00 - ET1.31)
input / output
2-fold
T1
−
−
−
T2
−
−
−
GB - 2
D - 2
Werbung
