Werbung
Verfügbare Sprachen
Verfügbare Sprachen
14005 Backrest
for »Gomezz«
- a useful addition to 14000 drummer throne »Gomezz«
- easy to setup and break down, great for on the road
- height and depth adjustable
Thank you for choosing this product. The instructions provide directions to all of the
important set up and handling steps. We recommend you keep these instructions for
future reference.
SAFETY NOTES
- Prior and after use the stand should undergo visual inspection, to ensure that all compo-
-
nents are there and to ensure that the product is in working order, to the extent visible.
- Damaged stands may not be used i.e. they must undergo a repair by a qualified technician.
- The option to adjust various settings on the product can result in the risk of pinching/
-
wedging your fingers. Careful and attentive handling during setup, operation and
-
disassembly is indispensable.
- Tighten the clamp screws - without the use of tools.
-
Manual strength is enough, over-tightening can negatively affect the components.
- Only to be used indoors
COMPONENTS
1 Backrest cushion with threaded bolt - 2 Backrest - 3 Backrest bracket
4 Accessory bag: a Guide rail - b Clamping screw M8 x 18 mm - c Wing nut M8
4 Accessory bag:
d Hexagon screw M6 x 25 mm - e washer ø 8,4 mm
4 Accessory bag:
f washer ø 6,4 mm - g Key SW10/13
INSTALLATION & FUNCTION
PREPARE THE »GOMEZZ« DRUMMER THRONE
5 There are 4 threaded bushings on the bottom of the »Gomezz« seat.
5
The bracket 3 is screwed in and the long-slit points to the middle of the seat.
5
Use the 4 hexagonal screws M6 x 25 mm 4 d and washer ø 6.4 mm 4 e
5
as well as the SW13 key 4 g.
ATTACH THE BACKREST
6 Clip the guide rail 4 a to the short section of the L-bracket 2.
6
The connection is good if:
6 a ...the guide rail and the L-bracket are lined up properly
6 b ...both of the guide rail knobs fit into the two drill holes of the L-bracket
6 c ...the four barbs click into place on the L-bracket
7 The bolt of the backrest cushion 1 is placed through the slit in the L-bracket 2.
7 a To ensure that the backrest cushion does not twist and remains in a horizontal
7 a
position, both knobs must be placed in the L-bracket slit.
7 b Now place the washer 4 f and securely tighten the wing nut 4 c
7 c The rounded section of the backrest cushion 1 faces upwards.
7 c
The cushion may also be turned 180° and attached.
ATTACH THE BACKREST TO »GOMEZZ«
8 Place the short section of the L-bracket in the holding bracket below
8
the seat cushion.
9 Now coming in from below place the clamping screw 4 b with the washer 4 f
9
into the long slit of the holding bracket into the female thread of the
9
L-bracket and tighten.
POSITION THE BACKREST
10 Height: Loosen the wing nut 4 c somewhat and place the
10 Height:
backrest in the desired position. Re-tighten the wing nut.
11 Depth: Loosen the clamping screw 4 b somewhat and place the
11 Depth:
L-bracket in the desired position. Re-tighten the finger screw.
MAINTENANCE
- In the event of workstation maintenance pay attention to possible risks
-
(wedging or pinching of fingers)
- To care for the product, use a damp cloth and a non-abrasive cleaning agent
FAULT-FINDING (F) and REPAIR (R)
F: The backrest is not stable: R: Tighten the clamping screw 9
F: Rückenlehne wackelt:
R: The guide is not installed properly? (refer to 6 a, b, c)
F: Rückenlehne wackelt:
R: Check the holding bracket 3 to make sure it is stable
F: The backrest is not stable and twists:
F: Rückenlehne wackelt:
B: Tighten the wing nut 7 b
F: Rückenlehne wackelt:
B: Both knobs 7 a, 7 c must disappear into the slit
TECHNICAL DATA
Backrest: Steel, chrome
Holding and adjustment bracket: Steel, powder coating, black
Material
Connection elements: Steel, galvanized
Guide bracket, handles: PA, black
Backrest cushion: Imitation leather, black
Dimensions Backseat cushion: 400 x 235 mm; Backrest: 430 x 185 x 45 x 6 mm
Box
470 x 325 x 90 mm
Weight
gross: 2.85 kg, net: 2.5 kg
KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
14005-000-02 Rev.04 03-80-657-00 3/17
All manuals and user guides at all-guides.com
COMPONENTS
PREPARE THE »Gomezz« DRUMMER THRONE
ATTACH THE BACKREST
ATTACH THE BACKREST TO »GOMEZZ«
PE Bag
Box
POSITION THE BACKREST
Adjustment
Area
Height
Depth adjustment
Werbung
