nedis SmartLife ZBSM10WT Kurzanleitung

a
Zigbee motion sensor ZBSM10WT
Intended use
The Nedis ZBSM10WT is a wireless, battery powered
motion sensor.
You can connect the product wirelessly to the Nedis
SmartLife app via the Zigbee gateway.
When connected, the current and past motion detection
is displayed in the app and can be programmed to trigger
any automation.
The product is intended for indoor use only.
The product is not intended for professional use.
Any modification of the product may have consequences
for safety, warranty and proper functioning.
Specifications
Product
Article number
Dimensions (l x w x h)
Battery lifetime
Zigbee frequency range
Maximum transmit power
Antenna gain
Temperature range
Operating humidity
Detection range
Main parts (image A)
1
Function button
2
Status indicator LED
Safety instructions
WARNING
-
•
Ensure you have fully read and understood the
instructions in this document before you install or use
the product. Keep this document for future reference.
•
Only use the product as described in this document.
•
Do not use the product if a part is damaged or
defective. Replace a damaged or defective product
immediately.
•
Do not drop the product and avoid bumping.
•
This product may only be serviced by a qualified
technician for maintenance to reduce the risk of electric
shock.
•
Do not expose the product to water or moisture.
•
Children should be supervised to ensure that they do
not play with the product.
•
Always keep button cell batteries, both full and empty,
out of reach of children to avoid the chance of
swallowing. Dispose of used batteries immediately and
safely. Button cell batteries can cause serious internal
chemical burns in as little as two hours when
swallowed. Keep in mind that the first symptoms may
look like child diseases like coughing or drooling. Seek
immediate medical attention when you suspect that
batteries have been swallowed.
•
Only power the product with the voltage
corresponding to the markings on the product.
•
Do not recharge non-rechargeable batteries.
•
Do not dismantle, open or shred secondary cells or
batteries.
•
Do not expose cells or batteries to heat or fire. Avoid
storage in direct sunlight.
•
Do not short-circuit a cell or a battery.
•
Do not store cells or batteries haphazardly in a box or
drawer where they may short-circuit each other or be
short-circuited by other metal objects.
•
Do not subject cells or batteries to mechanical shock.
•
In the event of a cell leaking, do not allow the liquid to
come in contact with the skin or eyes. If contact has
been made, wash the affected area with copious
amounts of water and seek medical advice.
•
Observe the plus (+) and minus (–) marks on the cell,
battery and equipment and ensure correct use.
•
Do not use any cell or battery which is not designed for
use with the equipment.
•
Seek medical advice immediately if a cell or a battery
has been swallowed.
•
Always purchase the battery recommended by the
product manufacturer for the product.
•
Keep cells and batteries clean and dry.
•
Wipe the cell or battery terminals with a clean dry cloth
if they become dirty.
•
Use only the cell or battery in the application for which
it was intended.
•
When possible, remove the battery from the product
when not in use.
•
Properly dispose of the empty battery.
•
Battery usage by children should be supervised.
•
Some wireless products may interfere with implantable
medical devices and other medical equipment, such as
pacemakers, cochlear implants and hearing aids.
Consult the manufacturer of your medical equipment
for more information.
•
Do not use the product at locations where the use of
wireless devices is prohibited due to potential
interference with other electronic devices, which may
cause safety hazards.
Connecting to the Zigbee gateway
4
Make sure the Zigbee gateway is connected to the
Nedis SmartLife app.
4
For information on how to connect the gateway to the
app, consult the manual of the gateway.
1. Open the Nedis SmartLife app on your phone.
2. Select the Zigbee gateway to enter the gateway
interface.
3. Tap Add subdevice.
4. Remove the battery insulation tab A
The status indicator LED A
pairing mode is active.
4
If not, press and hold the function button A
seconds to manually enter the pairing mode.
5. Tap to confirm A
The sensor appears in the app when the product is
successfully connected to the gateway.
Installing the sensor
1. Remove the film of the tape.
2. Stick the product onto a clean and flat surface.
The product is now ready for use.
The overview screen of the sensor
1. Open the Nedis SmartLife app on your phone.
2. Select the sensor you want to view.
The app shows the measured values of the sensor.
•
Tap Set alarm to switch the low battery alarm on or off
for the selected sensor.
Creating an automated action
1. Open the Nedis SmartLife app on your phone.
2. Tap Smart scenes at the bottom of the home screen.
3. Tap Automation to open the automation interface.
4. Tap + in the top right corner.
Here you can fill in different options to create an
automation.
5. Tap Save.
The new automation appears in the automation interface.
Removing the product from the app
1. Open the sensor interface.
2. Tap the pencil icon in the top right corner.
3. Tap Remove Device.
Declaration of Conformity
We, Nedis B.V. declare as manufacturer that the product
ZBSM10WT from our brand Nedis®, produced in China,
has been tested according to all relevant CE standards
and regulations and that all tests have been passed
successfully. This includes, but is not limited to the RED
2014/53/EU regulation.
The complete Declaration of Conformity (and the safety
datasheet if applicable) can be found and downloaded via:
nedis.com/zbsm10wt#support
Quick start guide
For more information see the extended manual
online: ned.is/zbsm10wt
2
Zigbee motion sensor
ZBSM10WT
46 x 46 x 30 mm
1 year
2405 - 2480 GHz
10 dBm
2.8 dBi
0 °C - 40 °C
< 100 % RH
Up to 7 m
3
Battery insulation tab
2
starts blinking to indicate
is blinking.
3
.
1
for 5