Werbung
Verfügbare Sprachen
Verfügbare Sprachen
1. Odbiornik nie działa:
a. Sprawdź podłączenie zasilania i odbiornika.
b. Jeżeli kontrolka czujnika działa poprawnie, sprawdź odbiornik.
c. Jeśli wskaźnik wykrywania ruchu nie świeci się, sprawdź poziom natężenia oświetlenia otoczenia i ustawienie czujnika zmierzchowego.
d. Sprawdź czy napięcie zasilania jest zgodne z wymaganiami.
2. Słaba czułość:
a. Sprawdź czy przed czujnikiem nie znajdują się urządzenia, które mogą zakłócić odbierane sygnały.
b. Sprawdź czy wykrywany obiekt znajduje się w polu detekcji
c. Sprawdź wysokość instalacji.
d. Sprawdź, czy temperatura otoczenia nie jest zbyt wysoka.
3. Czujnik nie może automatycznie wyłączyć odbiornika:
a. W polu detekcji występują ciągłe sygnały ruchu.
b. Sprawdź czy pokrętło TIME nie jest ustawione na najdłuższą wartość.
c. Sprawdź czy zasilanie jest zgodne z instrukcją.
Konserwację wykonuj przy odłączonym zasilaniu.
Czyść wyłącznie delikatnymi i suchymi tkaninami.
Nie używaj chemicznych środków czyszczących.
Nie zakrywaj wyrobu.
EN
An electrical device designed to automate the switching on and off of electrical devices when motion is detected by a PIR sensor. It is switched on at the appropriate
light intensity.
Functions:
- TIME operation adjustment
- LUX ambient light intensity adjustment
- SENS range adjustment
Since the detector reacts to temperature changes, avoid the following situations:
− Avoid directing the sensor towards objects with highly reflective surfaces such as mirrors etc.
− Avoid mounting the sensor close to heat sources such as vents, air conditioning units, lights, etc.
− Avoid directing the sensor towards objects that can move in the wind, such as curtains, tall plants, etc.
• Place the device in the socket.
• After connecting any electrical device, set the sensor parameters and test it.
The built-in twilight sensor detects day and night. Adjustment is carried out smoothly with the LUX knob in the range from 3 (night conditions) to 2000 lux.
Adjustable SENS range from 2m to 9m.
Adjustable TIME switching on - minimum time is 10 sec. ±3 sec. The maximum time is 15 min ±2 min. The time is counted from the last detection. The sensor's delay
time is counted continuously: if the next inductive signal is applied to the first one, it is restarted.
• Turn the LUX knob clockwise to maximum
• Turn the TIME knob counterclockwise for 10 seconds.
• Turn the SENS knob clockwise to maximum (+).
• Plug any electrical device into the socket. The sensor will warm up in 30 seconds and then go into operation.
• If the sensor receives an inductive signal, the lamp will switch on.When there is no other inductive signal, the load should stop working within 10s ±3s and the lamp
will switch off.
• Turn the LUX knob counterclockwise to minimum (3). If the ambient light intensity is higher than 3LUX, the sensor will not work and the lamp will also stop working.
If the ambient light intensity is less than 3LUX (darkness), the sensor will operate. In the absence of an inductive signal, the sensor should stop working within 10s±3sec.
Note: When testing the device in daylight, turn the LUX knob to SUN
than 60W/10W LED, the distance between the lamp and the sensor should be at least 60 cm.
1. The load does not work:
a. Please check if the connection of power source and load is correct.
b. If the sensor indicator light works correctly, check the receiver.
c. If the motion detection indicator is not illuminated, check the ambient light level and twilight sensor setting.
d. Please check that the power supply voltage is compatible with the specifications.
2. The sensitivity is poor:
a. Please check if there is any hindrance in front of the detector to affect it to receive the signals.
b. Please check that the detected object is in the detection area.
c. Please check the installation height.
d. Please check if the ambient temperature is correct.
3. The sensor cannot automatically switch off the receiver:
a. Please check if there is continual signal in the detection field.
b. Please check if the time delay is set to the maximum position.
c. Please check if the power corresponds to the instruction.
Maintenance should be carried out with power disconnected.
Clean only with delicate and dry fabrics.
Do not use chemical cleaners.
Do not cover the product.
NIEKTÓRE PROBLEMY I SPOSOBY ROZWIĄZANIA
BEZPIECZEŃSTWO I KONSERWACJA
CHARACTERISTICS
IMPORTANT
INSTALLATION
OPERATION – TEST THE DEVICE
, otherwise the sensor will not function properly! If the connected lamp has a power greater
SOME PROBLEMS AND SOLUTIONS
SAFETY AND MAINTENANCE
3
Operating and installation instructions
Werbung
