Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating Instructions
WLAN Access Point and Range Extender
300 Mbit/s 2.4 GHz + 433 Mbit/s 5 GHz
Order No. 2300465
Intended use
The product has 3 operating modes: "Repeater", "Access Point" (AP) and "Router". The "Re-
peater" mode serves to amplify your existing WLAN network and expand the coverage area.
The "Access Point" (AP) mode provides a separate WLAN network.
The "Router" mode serves to connect the devices that are connected to the product to the
Internet using your existing modem.
You can connect your devices to the product in all modes via WLAN or LAN.
Power is supplied through the mains socket into which the product is plugged. For safety and
compliance reasons, you may not convert and/or modify the product in any way. If you use the
product for purposes other than those described above, the product can be damaged. Moreo-
ver, improper use involves risks such as short-circuits, fire, electric shocks, etc. Please read
the operating instructions carefully and keep them. Please include these operating instructions
when you pass the product on to a third party.
This product complies with the applicable national and European regulations. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
Package contents
• WLAN Access Point and Range Extender 300 Mbit/s 2.4 GHz + 433 Mbit/s 5 GHz
• RJ45 cable
• Operating instructions
Latest operating instructions
Download the latest operating instructions at
www.conrad.com/downloads or scan the QR code shown. Follow the instruc-
tions on the website.
Explanation of symbols
The lightning symbol inside a triangle is used when there is a potential risk of per-
sonal injury, e.g. through an electric shock.
An exclamation mark in a triangle indicates important instructions in this operating
manual which absolutely have to be observed.
The arrow symbol indicates specific tips and advice on operation.
Safety Instructions
Please read the operating instructions carefully and pay particular attention
to the safety instructions. We do not assume liability for any injuries/mate-
rial damages resulting from failure to observe the safety instructions and the
information in these operating instructions regarding the proper use of the
product. Furthermore, in such cases, the warranty/guarantee will be null and
void.
a) Product
• The design of the product complies with Safety Class II. Only a standard mains
socket connected to the public supply may be used as the power source for the
device.
• If the product is damaged, do not touch it; there is a danger to life from electric
shock!
First completely switch off the mains voltage to the mains socket to which the
power adapter is connected (e.g., switch off at the corresponding circuit breaker
or remove the safety fuse and then switch off the corresponding RCD). Only
then unplug the power adapter from the mains socket and take the product to a
specialised workshop.
• Check the product for damage before each use!
• If you detect any damage, do NOT connect the product to the mains voltage! This
may cause fatal injury!
• The product is suitable for dry, enclosed indoor areas only. It must not be allowed
to become damp or wet; never handle it if your hands are wet!
• There is a risk of a life-threatening electric shock!
b) General
• Protect the product from extreme temperatures, direct sunlight, strong vibrations,
high humidity, moisture, combustible gases, vapours and solvents.
• The product is not a toy. Keep out of the reach of children and pets.
• Do not carelessly leave the packaging material lying around. It may become a
dangerous plaything for children.
• Handle the product with care; it can be damaged by impacts, blows or falls even
from a low height.
• If you have any questions that are not answered in this manual, please contact
our technical service or another specialist.
Product overview
1 „Power"
lights up as soon as the device is switched on
2 „LAN"
lights up when connected; flashes during data transfer
3 „WAN/LAN"
lights up when connected; flashes during data transfer
4 „WIFI/WPS"
lights up when WLAN is active; flashes fast while creating a
connection to your router; flashes slowly during the attempt to
create a connection to a device
5 Slider switch for mode selection
6 „WPS" button
Press and hold button 6 seconds for the connection to a router;
press and hold button 3 seconds for the connection to a device
(e.g. computer)
7 countersunk "Reset" button
8 LAN connection
9 WAN/LAN connection
Standard settings:
Configuration address:
Standard IP address:
Username/password:
WLAN-SSID 2,4 GHz:
WLAN-SSID 5 GHz:
Connection and start-up
• Select the desired operating mode using the slider switch for the mode selection (5). The
modes "Router" and "Access Point" (AP)/"Repeater" are available for selection.
• If you want to use the product as "Access Point" and have selected the correct mode, con-
nect the WAN/LAN port to a network connection of your router using a network cable con-
nected 1 to 1.
• If you have selected the "Router" mode, connect the WAN/LAN port to the corresponding
port of your modem using a network cable connected 1 to 1. Switch on your modem.
• Plug the device into a mains outlet and wait until the start-up process has completed. This
takes approx. 2 minutes.
Quick setup of "Repeater" via WPS
Please note that the slider switch for mode selection (5) must be in the "AP/Re-
peater" position for you to be able to carry out the configuration via WPS.
During the configuration, the repeater clones the WLAN name and password of your
WLAN router. At the end, an identifier is added to the WLAN name so that you can
differentiate between the WLAN of your router and that of the repeater.
• To start the automatic configuration via WPS, press the WPS button (6) on the repeater for
longer than 6 seconds.
Then release the button. The WIFI/WPS LED (4) begins to flash fast
5 6 7 8
1
2
3
4
http://ap.setup
192.168.10.1
admin
Wireless-N
Wireless-AC
9
Werbung
Inhaltsverzeichnis
