DeWalt DWE625 Originalanweisung Seite 34

EngLIsH
Installing and Removing a Cutter (Fig. C, F)

WARNING: Do not tighten the collet without a
cutter fitted.

WARNING: Always use cutters with shanks which match
the diameter of the collet.

WARNING: Do not use cutters larger than 50 mm (2")
unless the router is fitted in a router table.

CAUTION: Care should be taken when removing cutter to
avoid cuts to fingers.
Installing a Cutter
1. Insert at least three fourths of the shank length of the cutter
into the collet assembly
2. Press the spindle lock 8
is locked.
nOtE: You may need to turn the spindle slightly to
engage it.
3. Turn the collet nut 36
22 mm wrench 13 to tighten it.
Removing a Cutter
1. Press the spindle lock button
spindle is lock.
2. Turn the collet nut 9 clockwise with the supplied 22 mm
wrench 13 to loosen.
3. Keep turning the wrench until the collet nut tightens and
then loosens again. This is the fail‑safe mechanism releasing
the collet.
4. The cutter should now slide out.
nOtE: Each time you finish using a cutter, remove it and
store it in a safe place.
Fine Height Adjuster (Fig. A, D, E)

CAUTION: Ensure that the plunge locking lever is
unlocked. Never use unnecessary force to rotate the fine
height adjuster mechanism.

CAUTION: Do not remove the screw on hex nuts.
The fine height adjuster can be used in portable mode or when
the router is held inside a table.
Adjusting the Depth of Cut (Fig. A, D, E)
Your router is equipped with a high‑precision depth adjustment
system including a zero reset ring for both the quick height
adjuster and the fine height adjuster.
Quick adjustment Using the graduation with Zero Reset Ring
1. Loosen the depth stop quick height adjuster lock
2. Unlock the plunge limiter by pushing the release
lever 6 down.
3. Lower the router carriage until the cutter is in contact with
the workpiece.
4. Press the quick locking button
5. Set the quick height adjuster
adjust reset ring 19 to zero. The depth stop bar
in contact with the turret stop
32
9 .
forward until the router spindle
counterclockwise with the supplied
8 forward until the router
15
7 .
16 to zero and reset the fine
12
11 .
6. Adjust the depth of cut using the quick height adjuster
and the corresponding graduation. The adjusted depth of
cut is indicated by the pointer
7. Tighten the quick height adjuster lock
Fine adjustment
When not using a depth template, or if the depth of cut
needs readjustment, it is recommended to use the fine height
adjuster 18 .
1. Adjust the depth of cut as described in Adjusting the Depth
of Cut.
2. Set the fine height adjuster to zero using the fine zero reset
ring 19
3. Rotate the fine height adjuster
position: one turn corresponds to approximately 1 mm and
1 mark to 0.1 mm.
Fitting a Guide Bush (Fig. H)
Together with a template, guide bushes play a valuable part in
cutting and shaping to a pattern.
• Fit the guide bush
screws 25
Fitting the Parallel Fence (Fig. I, J)
1. Fit the guide rod
2. Slide the parallel fence
3. Tighten the wing bolts
Adjusting the Parallel Fence (Fig. A, I, J)
1. Draw a cutting line on the material.
2. Lower the router carriage until the cutter is in contact with
the workpiece.
3. Push quick release button
using the thumb wheel
4. Position the router on the cutting line.
5. Slide the parallel fence
tighten the wing bolts
6. Adjust the parallel fence using the fine adjustment knob
The outer cutting edge of the cutter must coincide with the
cutting line.
7. If required, loosen the screws
to obtain the desired guiding length.
Dust Extraction (Fig. A, K, P)
Dust from materials such as lead‑containing coatings and some
wood types, can be harmful to one's health. Breathing‑in the
.
dust can cause allergic reactions and/or lead to respiratory
infections of the user or bystanders.
Certain dust, such as oak or beech dust, is considered
carcinogenic, especially in connection with
wood‑treatment additives.
Observe the relevant regulations in your country for the
materials to be worked.
The vacuum cleaner must be suitable for the material
must be
being worked.
When vacuuming dry dust that is especially detrimental to
health or carcinogenic, use dust class M vacuum cleaner.
17 .
18 to the required
24 to the router base
as shown.
26 to the router base
27 over the rods.
28 temporarily.
7 and limit the carriage return
4 .
27 against the workpiece and
28 .
30 and adjust the strips
16
15 .
10 using the
10 .
29 .
31