Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Service Test Programme
23b (VideoColDencOff)
Diagnostic Nucleus VideoColDencOff disables colour bar in the DENC
in the STi5505.
Correct operation cannot be detected by the Diagnostic Software but
must be checked externally.
25a (VideoScartLo)
VideoScartLo steers pin 8 on the Euro AV connector with the value Low
(0 to 0.5V)
Correct operation cannot be detected by the Diagnostic Software but
must be checked externally.
25b (VideoScartMi)
VideoScartMi steers pin 8 on the Euro AV connector with the value
Medium (6V ±10%)
Correct operation cannot be detected by the Diagnostic Software but
must be checked externally.
25c (VideoScartHi)
VideoScartHi steers pin 8 on the Euro AV connector with the value High
(12V ±10%).
Correct operation cannot be detected by the Diagnostic Software but
must be checked externally.
26 (DispVer)
Get version number of the slave processor on the Eject PWB
31 (LogReadErr)
Read error log from NVRAM and output the data as error numbers only.
32 (LogReadBits)
Read error bits from NVRAM and output the numbers of the error bits
which are set.
Error Message
Command not allowed in this state or
unknown
parameter not valid for command
sledge could not be moved to home position
focus failure
motor not on speed within time-out
servo didn't get on track after several retries
PLL could not lock in Accessing or
Tracking state
subcode or sector information could
not be read
requested subcode item could not be found
tray could not be closed or opened
completely
TOC read could not be read in time
Set when a seek couldn't be performed
datapath tries to access a non existing
lead in area
A non existing burts cutting area is
requested
S2b communikation error
S2b communikation error
S2b communikation error
S2b communikation error
S2b communikation error
communikation error with the STi 5505
communikation error with the STi 5505
communikation error with the display
processor
33 (LogReset)
Reset all error log and bits in the NVRAM.
34 (MiscReadConfig)
Read configuration area from NVRAM and output as raw data.
35 (MiscNvramReset)
Reset the whole NVRAM to zero.
After resetting the NVRAM the Player must be reactivated
(page 1-6)!
2 - 8
36 (MiscNvramMod)
Read/Modify any location in NVRAM.
37 (BeVer)
Get version number of the Drive Mechanism.
38a (BeFocusOn)
Diagnostic Nucleus BeFocusOn puts the laser of the BE into focus
(focus loop).
38b (BeFocusOff)
Diagnostic Nucleus BeFocusOff switches the focus loop off.
39a (BeDiscmotorOn)
BeDiscmotorOn switches the disc motor (=spindle motor) on
39b (BeDiscmotorOff)
BeDiscmotorOff switches the disc motor (=spindle motor) off
40a (BeRadialOn)
Diagnostic Nuclei BeRadialOn closes the radial loop
40b (BeRadialOff)
Diagnostic Nuclei BeRadialoff opens the radial loop
41a (BeSledgeIn)
Diagnostic Nuclei BeSledgeIn moves the sledge inwards.
41b (BeSledgeOut)
Diagnostic Nuclei BeSledgeOut moves the sledge outwards.
42a (BeGroovesIn)
Diagnostic Nuclei BeGroovesIn lets the laser spot jump to the inside
limit of the disc.
42b (BeGroovesMid)
Error Log Error bits
Diagnostic Nuclei BeGroovesMid lets the laser spot jump to the middle
of the disc.
150101
8
42c (BeGroovesOut)
150102
7
Diagnostic Nuclei BeGroovesOut lets the laser spot jump to the outside
limit of the disc.
150103
6
150104
5
43a (BeTrayIn)
Diagnostic Nucleus BeTrayIn closes the disc tray.
150105
4
43b (BeTrayOut)
150106
3
Diagnostic Nucleus BeTrayOut opens the disc tray.
150107
2
44 (BeReset)
150108
1
Reset the Drive Mechanism.
46 (MiscApplVer)
150109
16
Read the version of the application software from the NVRAM.
15010A
15
47a (MiscBeTrayOpen)
Read the total number of times tray open from a fixed location in the
15010B
14
NVRAM.
15010C
13
47b (MiscBePower)
15010D
12
Read the total time of power on from a fixed location in the NVRAM.
47c (MiscBePlayTimeCDDA)
15010E
11
Read the total playtime in CDDA mode from a fixed location in the
NVRAM.
1501F0
10
47d (MiscBePlayTimeDVD)
1501F1
9
Read the total playtime in DVD mode from a fixed location in the
1501F3
24
NVRAM.
1501F4
23
55a (VideoScartSwDvd)
1501F5
22
Activated the signal path from DVD to TV.
90000
32
55b (VideoScartSwPass)
90001
31
Activated the signal path from AUX to TV.
190000
40
GDV Modul 1
GRUNDIG Service
Werbung
Inhaltsverzeichnis
