Symbols Used In The Manual - Crown CT15258 Originalbetriebsanleitung

Seite von 137

/ 137
Inhalt
Inhaltsverzeichnis
Lesezeichen

Inhaltsverzeichnis

Verfügbare Sprachen

accessory may contact hidden wiring or its own

cord. Cutting accessory contacting a "live" wire may

make exposed metal parts of the power tool "live" and

could give the operator an electric shock�

Safety guidelines during power tool

operation

• Fix the workpiece. Use a fixing device or a vice to fix

the work piece for safely and steadily�

• Take necessary and proper safety measures when

harmful, flammable or explosive dust is produced in

the work� For example, dust that may cause cancer is

produced during the operation� Please use dust and

chip collecting device and wear a dust mask in the

work�

• Keep workplace tide and clean� The mixed materials

would be extremely dangerous� Light metal dust would

be combusted and explode easily�

• Do not process materials that contain asbestos� As-

bestos is cancerogenic substance�

• Put down the power tool when the saw blade is fully

stopped�

• Do not use power tool when cable is damaged� If

the power wire is damaged or broken in the work, do

not touch it and pull out the plug immediately� Using

broken wire would lead to electric shock easily�

• Keep hands away from sawing area� Hand shall not

hold the lower part of work piece� Your hand would be

cut when it touches saw blade�

• First start the power tool and then put the power tool

of the workpiece to process it� If the saw blade is stuck

in the workpiece and power tool would rebound�

• Attention: the base plate shall cling to the workpiece

during the sawing. If the saw blade is deflected, it

would be broken and power tool would rebound�

• Cut off the power of power tool when work is done

and take the saw blade when the power tool is fully

stopped� The power tool wouldn't rebound in this way

and it can be put down safely�

• Use undamaged and crackles saw blade only�

Bended or dull saw blade would be broken easily and

cause rebound of power tool�

• After the power tool is shut down, do not stop the

moving saw blade by side pressure� The blade saw

would be damaged or broken and further lead to re-

bound in this way�

• Use proper detector to detect whether there is con-

cealed circuit and pipeline in the operation area and

ask the local construction organization for assistance

if necessary� In the work, if the cable is cut off, it would

cause fire disaster and electric shock. Damaged gas

pipe would explode� If the water pipe is cut off, it would

cause property losses and electric shock to the opera-

tor�

• Fix the saw blade rigidly with the saw holder� Check

the fixing of the saw blade regularly.

• If the used saw blade is not intended for cutting met-

als, remove any metal objects (nails, screws, hinges,

etc�) before work�

• Avoid stopping an power tool motor when loaded�

• During operation watch the position of a power cable

(it should always be positioned behind the power tool)�

Do not allow it to whip around your legs or arms�

• Should power supply fail during work, immediately

turn the power tool's switch "Off" in order to avoid ac-

cidental turning of the power tool on�

• After the power tool is switched off, the saw blade

keeps moving mechanically for some time, therefore

put the power tool aside only after the saw blade is

completely immobile�

• The saw blade gets quite hot during the operation,

therefore do not touch the saw blade until it is com-

pletely cooled off�

Warning: the chemical substances con-

tained in dust generated in sanding, cut-

ting, sawing, grinding, drilling and other

construction industry activities may

result in cancer, congenital deficiency or be harm-

ful to the fertility. The ion of some chemical substanc-

es shall be:

• before any repair and replacement work to the

machine, the power plug must be pulled out firstly;

• the transparent two silicon oxide and other ma-

sonry products in the wall bricks and cement; the

chromium arsenic (CCA) in wood with chemical

treatment� The harm degree of these substances

shall depend on the frequent degree of you carrying

out these works� If you want to reduce the contact

with these chemical substances, please work in the

place with ventilation and you shall use the appli-

ances with safety certificates (such as the dust mask

designed with tiny dust filter).