Herunterladen Diese Seite drucken

OSRAM OPTOTRONIC OT FIT 15/220-240/350 NFC Installationsanleitung Seite 2

Werbung

OT FIT 15/220-240/350 NFC | OT FIT 25/220-240/700 NFC | OT FIT 40/220-240/1A0 NFC
Installing and operating information: Connect only LED load type. LED
module will be switched off when output voltage drops below 18V or rises above
40V. Wiring information (see fig. A): Do not connect the outputs of two or more
units. Output current adjustment via NFC (Near Field Communication) in mains
off mode only. Unit is permanently damaged if mains is applied to the terminals
21/22. Lines 21/22 max. 2 m whole length excl. modules. Hot plug-in or second-
ary switching of LEDs is not permitted. Hereby OSRAM GmbH declares that the
radio equipment types OT FIT 15 NFC, OT FIT 25 NFC and OT FIT 40 NFC are
in compliance with Directive 2014/ 53/ EU and the relevant statutory instruments.
The full text of the EU declaration of conformity or the UK-declaration of con-
formity is available at the following internet address: www. osram. com/ot-indoor-
ce. Frequency range: 13 553 – 13 567 kHz Technical support: www.osram.com,
+49 (0)89-6213-6000 1) Constant current LED Power Supply; 2) t c point; 3) Made
in China; 4) picture only for reference, valid print on product; 5) Mains; 6) Input;
7) Output; 8) Year; 9) Week
Installations- und Betriebshinweise: Schließen Sie nur LED-Lasttypen an.
Das LED-Modul wird abgeschaltet, wenn die Ausgangsspannung unter 18V sinkt
oder über 40V steigt. Verdrahtungshinweise (siehe Abb. A): Die Ausgänge von
zwei oder mehreren Geräten dürfen nicht verbunden werden. Die Ausgangs-
stromeinstellung erfolgt nur im netzspannungsfreien Zustand über NFC (Nahfeld-
kommunikation). Das Gerät wird dauerhaft beschädigt, wenn an die Klemmen
21/22 Netzversorgung angelegt wird. Max. Gesamtlänge der Leitungen 21/22
ohne Module 2m. Der Anschluss von LEDs im laufenden Betrieb oder sekundär-
es Schalten ist nicht zulässig. Hiermit erklärt die OSRAM GmbH, dass die Funk-
anlagentypen OT FIT 15 NFC, OT FIT 25 NFC und OT FIT 40 NFC der Richtlinie
2014/53/EU entsprechen. Der vollständige Text der EU-Konformitätserklärung ist
unter der folgenden Internetadresse verfügbar: www.osram.com/ot-indoor-ce.
Frequenzbereich: 13 553 – 13 567 kHz Technische Unterstützung: www.osram.
com, +49 (0)89-6213-6000 1) Konstantstrom-LED-Betriebsgerät; 2) t c -Punkt;
3) Hergestellt in China; 4) Foto dient nur als Referenz, gültiger Aufdruck auf dem
Produkt; 5) Netzversorgung; 6) Eingang; 7) Ausgang; 8) Jahr; 9) Woche
Informations pour l'installation et le fonctionnement : Branchement avec
type de charge LED uniquement. La coupure de charge survient si la tension
de sortie US est inférieure à 18V / supérieure à 40V. Informations de câblage
(voir fig. A) : Ne pas brancher les sorties de deux unités ou plus. Configuration
du courant de sortie via NFC (Near Field Communication). Coupez impérative-
ment l'alimentation secteur au préalable. Le raccordement secteur aux terminaux
21/22 causera des dommages irréversibles à l'unité. Lignes 21/22 longueur
totale max. 2 m hors modules. Le branchement à chaud ou la commutation
secondaire des LED ne sont pas autorisés. OSRAM GmbH atteste par la présente
de la conformité des équipements radio OT FIT 15 NFC, OT FIT 25 NFC ou OT
FIT 40 NFC avec la directive 2014/53/UE. Le texte de cette déclaration UE de
conformité peut être consulté dans son intégralité à l'adresse suivante  :
www. osram. com/ot-indoor-ce. Bande de fréquences : 13 553 – 13 567 kHz
Support technique : www.osram.com, +49 (0)89-6213-6000 1) Alimentation LED
courant constant; 2) Point T c ; 3) Fabrique en Chine; 4) image non contractuelle,
se référer aux inscriptions sur le produit; 5) Alimentation électrique; 6) Entrée;
7) Sortie; 8) Année; 9) Semaine
Informazioni su installazione e funzionamento: Collegare soltanto tipi di ca-
rico LED. Lo spegnimento del modulo LED avviene se la tensione di uscita è in-
feriore a 18V/superiore a 40V. Informazioni sul cablaggio (vedi figg. A): Non
connettere le uscite di due o più unità. Regolazione corrente in uscita via NFC
(Near Field Communication) solamente con rete in modalità spento. L'unità è
danneggiata permanentemente se la tensione di rete viene applicata ai terminali
21/22. Linee 21/22 max. 2 m di lunghezza totale, moduli esclusi. Non sono per-
messi l'hot swap o lo switching secondario dei LED. Con la presente, OSRAM
GmbH dichiara che gli equipaggiamenti radio di tipo OT FIT 15 NFC, OT FIT 25
NFC e OT FIT 40 NFC sono conformi alla direttiva 2014/53/EU. Il testo completo
della dichiarazione di conformità europea è disponibile sul seguente indirizzo:
www.osram.com/ot-indoor-ce. Intervallo di frequenza: 13 553 – 13 567 kHz
Supporto tecnico: www.osram.com, +49 (0)89-6213-6000 1) Alimentazione LED
a corrente costante; 2) Punto t c ; 3) Prodotto in Cina; 4) immagine solo come rife-
rimento, stampa valida sul prodotto; 5) Rete; 6) Ingresso; 7) Uscita; 8) Anno;
9) Settimana
Indicaciones de instalación y funcionamiento: Conecte solo tipo de carga
LED. Si el voltaje de salida es menor de 18V o mayor de 40V se producirá una
desconexión de carga del módulo LED. Indicaciones sobre cableado (véase la
fig. A): No conecte las salidas de dos o más unidades. Ajuste de la corriente de
salida mediante NFC (comunicación de campo cercano) solo con la red en modo
apagado. La unidad sufrirá daños permanentes si la red eléctrica se aplica a
los terminales 21/22. La longitud total máxima de las líneas 21/22 sin módulo
es de 2 m. No admite la conexión en caliente o una conmutación secundaria
de las LED. Por la presente, OSRAM GmbH declara que los equipos de radio
tipo OT FIT 15 NFC, OT FIT 25 NFC y OT FIT 40 NFC cumplen la directiva
2014/53/EU. Puede consultar el texto completo de la declaración de conformi-
dad de la EU en la siguiente dirección de internet: www.osram.com/ot-indoor-ce.
Gama de frecuencias: 13 553 – 13 567 kHz Asistencia técnica: www.osram.
com, o +49 (0)89-6213-6000 1) Fuente de alimentación LED con corriente
constante; 2) Punto t c ; 3) Hecho en China; 4) La imagen solo es de referencia;
la impresión válida se encuentra en el producto; 5) Red; 6) Entrada; 7) Salida;
8) Año; 9) Semana
2
Informação de instalação e funcionamento: Ligue apenas o tipo de carga
LED. O desligamento do módulo LED ocorre com tensão de saída inferior a 18V
ou superior a 40V. Informação sobre ligação dos cabos (fig. A): Não interligar
as saídas de duas ou mais unidades. Regulação da corrente de saída via NFC
(Near Field Communication) apenas com a tensão de rede desligada. A unida-
de será destruída se tensão da rede for aplicada aos terminais 21/22. Linhas
21/22 máx. 2 m de comprimento total excluindo os módulos. Hot-plug ou co-
mutação secundária de LEDs não são permitidos. Pelo presente, OSRAM GmbH
declara que os tipos de equipamento de rádio OT FIT 15 NFC, OT FIT 25 NFC
e OT FIT 40 NFC cumprem com a Diretiva 2014/53/UE. Pode consultar o
completo texto da declaração de conformidade no seguinte site da internet:
www.osram.com/ot-indoor-ce. Gama de frequências: 13 553 – 13 567 kHz
Assistência técnica: www.osram.com, +49 (0)89-6213-6000 1) Alimentação
elétrica do LED por corrente constante; 2) Ponto t c ; 3) Fabricado na China;
4) imagem apenas para referência, estampa válida no produto; 5) Linha de
alimentação elétrica; 6) Entrada; 7) Saída; 8) Ano; 9) Semana
Πληροφορίες εγκατάστασης και χειρισμού: Σύνδεση μόνο σε τύπο φορτίου
LED. Η μονάδα LED απενεργοποιείται όταν η τάση εξόδου είναι κάτω από 18V
ή πάνω από 40V. Πληροφορίες καλωδίωσης (βλ. εικ. A): Μην συνδέετε τις
εξόδους δύο ή περισσότερων μονάδων. Ρύθμιση ρεύματος εξόδου μέσω του
NFC (Near Field Communication - Επικοινωνία κοντινού πεδίου) μόνο σε λει-
τουργία απενεργοποίησης δικτύου. Η μονάδα υφίσταται μόνιμη βλάβη εάν οι
ακροδέκτες 21/22 συνδεθούν με τροφοδοσία ρεύματος. Γραμμές 21/22 2 μέτρα
μεγ. συνολικό μήκος, χωρίς τις μονάδες. Δεν επιτρέπονται εν λειτουργία βυσμά-
τωση και δευτερεύουσα ενεργοποίηση των LED. Δια του παρόντος, η OSRAM
GmbH δηλώνει ότι οι ραδιοφωνικοί εξοπλισμοί τύπου OT FIT 15 NFC, OT FIT
25 NFC και OT FIT 40 NFC είναι σύμφωνοι με την οδηγία 2014/53/EΕ. Το
πλήρες κείμενο της δήλωσης συμμόρφωσης ΕΕ είναι διαθέσιμο στην παρακάτω
διαδικτυακή διεύθυνση: www.osram.com/ot-indoor-ce. Εύρος συχνότητας:
13 553 – 13 567 kHz Τεχνική υποστήριξη: www.osram.com, +49 (0)89-6213-6000
1) Ηλεκτρική τροφοδοσία συνεχούς ρεύματος με LED; 2) Σημείο δοκιμής t c ;
3) Χώρα προέλευσης Κίνα; 4) Η εικόνα είναι ενδεικτική. Η έγκυρη εκτύπωση
είναι στο προϊόν; 5) Δίκτυο; 6) Είσοδος; 7) Έξοδος;8) Έτος; 9) Εβδομάδα
Installatie- en gebruiksinstructies: Sluit alleen het type voor LED-vermogen
aan. De LED-module wordt uitgeschakeld als de uitgangsspanning onder de
18V of boven de 40V komt. Informatie over bedrading (zie fig. A): Sluit niet de
uitgangen van twee of meer units aan. Aanpassing uitgangsstroom via NFC
(Near Field Communication) en alleen als de netstroom is uitgeschakeld. De
eenheid wordt permanent beschadigd als de netstroom wordt aangesloten op
de aansluitpunten 21/22. Leidingen 21/22 max. 2 m totale lengte excl. modules.
Hot plug-in of secundair schakelen van leds is niet toegestaan. OSRAM GmbH
verklaart hierbij dat de radioapparatuur OT FIT 15 NFC, OT FIT 25 NFC en
OT FIT 40 NFC aan Richtlijn 2014/53/EU voldoet. De volledige tekst van de
EU-conformiteitsverklaring is beschikbaar op het volgende internetadres:
www.osram.com/ot-indoor-ce. Frequentiebereik; 13 553 – 13 567 kHz Techni-
sche ondersteuning: www.osram.com, +49 (0)89-6213-6000 1) Constante stroom
LED voeding; 2) t c -punt; 3) Geproduceerd in China; 4) afbeelding slechts ter
informatie, zie geldig stempel op product; 5) Net; 6) Ingang; 7) Uitgang; 8) Jaar;
9) Week
Installations- och bruksinformation: Anslut endast LED-lampor. LED-mo-
dulen släcks när utspänningen sjunker till under 18V eller överstiger 40V. In-
kopplingsinformation (se fig. A): Koppla inte ihop kontakterna från två eller fler
enheter. Justering av utgående ström via NFC (närfältskommunikation) endast
med huvudströmmen bortkopplad. Permanenta skador kan uppstå i enheten
om huvudströmmen kopplas till terminalerna 21–22. Den maximal totala längden
på ledningarna 21/22 är 2 m utan moduler. Inkoppling av LED-lysdioder under
spänning är inte tillåtet. Härmed intygar OSRAM GmbH att radioutrustningen
av typen OT FIT 15 NFC, OT FIT 25 NFC och OT FIT 40 NFC överensstämmer
med direktiv 2014/53/EU. Den fullständiga texten i EU-försäkran om överens-
stämmelse finns på följande internetadress: www.osram.com/ot-indoor-ce.
Frekvensomfång: 13 553–13 567 kHz Teknisk support: www.osram.com,
+49 (0)89-6213-6000 1) Konstantström LED-strömförsörjning; 2) t c -punkt; 3) Till-
verkad i Kina; 4) Bild endast avsedd som referens, giltigt tryck på produkten;
5) Nätspänning; 6) Ingång; 7) Utgång; 8) År; 9) Vecka
Asennus- ja käyttötietoja: Kytke ainoastaan LED-kuormitustyyppiin. LED-
moduuli kytkeytyy pois päältä, kun lähtöjännite on alle 18V tai yli 40V. Kytken-
tätiedot (katso kaavio A): Älä kytke kahden tai useamman yksikön lähtöjä toi-
siinsa. Lähtövirran säätö NFC:n (Near Field Communication) kautta vain silloin,
kun sähköverkko ei ole käytössä. Yksikkö vahingoittuu pysyvästi, jos kytkentä-
rimat 21/22 liitetään sähköverkkoon. Linjat 21/22 maks. 2 m kokonaispituus.
LEDien käytönaikainen vaihto tai toissijainen kytkentä ei ole sallittua. OSRAM
GmbH vakuuttaa, että radiolaitetyypit OT FIT 15 NFC, OT FIT 25 NFC ja OT FIT
40 NFC ovat direktiivin 2014/53/EU mukaisia. EU-vaatimustenmukaisuusvakuu-
tuksen koko teksti on saatavissa verkko-osoitteesta www.osram.com/ot-indoor-
ce. Taajuusalue: 13  553 – 13  567  kHz Tekninen tuki: www.osram.com,
+49 (0)89-6213-6000 1) Tasavirtalähde led-moduuleille; 2) t c -piste; 3) Valmis-
tettu Kiinassa; 4) kuva on vain viitteellinen, tuotteeseen painettu on pätevä;
5) Verkkojännite; 6) Sisääntulo; 7) Ulostulo; 8) Vuosi; 9) Viikko

Werbung

loading

Diese Anleitung auch für:

Optotronic ot fit 25/220-240/700 nfcOptotronic ot fit 40/220-240/1a0 nfc