Technical Specifications; Parts List - JBM 53688 Bedienungsanleitung

REF. 53688
3. Insert the 12V cigarette lighter socket adaptor (15)
into the 12V output socket. The power will be con-
nected automatically.
NOTE! You can charge the jump starter by connecting it
to the car's 12V output socket, with a cord with cigarette
lighter socket adaptors on each end, but only as a tem-
porary arrangement.
Starting the engine
1. Completely stop the car and turn the jump starter's
switch to the "OFF" position.
2. Connect the red clamp to the battery positive pola-
rity.
3. Connect the black clamp to the vehicle chassis.
NOTE! Do not connect the black clamp into the negative
polarity.
4. Turn the jump starter's switch into the "ON" position.

TECHNICAL SPECIFICATIONS

Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12V/24V
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Ah Lead-acid battery AGM (2PCS)
Starting/Peak current 12V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1500A/3000A
Starting/Peak current 24V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 750A/1500A
Charger (230V/50Hz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12V outlets . . . . . . . . . . . . . . . . . 12V DC output socket (1PCS) (max. 15A current overload protection)
Charging time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 40h
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392x209x370mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16,3kg

PARTS LIST

2
4
3
5
11
1
7
8
9
10
6
13
15
14
12
· 5 ·
5. Turn the vehicle's ignition key to start the engine.
6. Once the engine is working, turn the jump starter's
switch into the "OFF" position.
7. Disconnect the red and black clamps.
Emergency light
1. To turn it on, press the LED emergency light button
(10).
2. To make it flicker as a warning light, press the LED
emergency light button a second time (10).
3. To turn it off, press the LED emergency light button
a third time (10).
Replacing the battery
1. Release all the screws from the rear cover.
2. Separate the front and rear covers; the battery ca-
sing is visible.
3. Remove the battery.
4. Release the positive and negative wires from the
battery.
5. Connect the positive and negative wires correctly to
new battery - the red wire to positive polarity and the
black wire to negative polarity.
6. Place the new battery into unit's casing.
7. Attach the rear cover properly with screws.
NUM DESCRIPTION
1 12V output socket
2 On/Off switch
3 Charging status LED light: Charging
4 Charging status LED light: Charged
5 Nut
6 LED emergency light
7 Warning light
8 Internal battery voltage status
9 Internal battery voltage test button
10 LED emergency light button
11 Charging socket
12 12/24 V switch
13 Indication light for 24 V
14 Charger
15 12V cigarette lighter socket adaptor
12V 1A