Operation; Important Remarks - JBM 53688 Bedienungsanleitung

EN
INSTRUCTION MANUAL
PRODUCT'S PRESENTATION
The jump starter is designed to start cars, boats and other
vehicles when the vehicle's battery cannot be used, avoi-
ding you the need to seek assistance from other drivers. It
is equipped with 12/24V power source, a LED light which
can be used in emergency situations, and LED lights that
indicates the battery's internal status. This jump starter
can be used to provide power to 12V DC appliances by
means of its 12V DC outlet socket and can be charged
with an external charger by connecting it to the charging
socket. It also has an automatic current overload protec-
tion for the battery.
SAFETY INSTRUCTRIONS
WARNING! Read all safety warnings and all instruc-
tions. Failure to follow the warnings and instructions lis-
ted below may result in electric shock, fire and/or serious
injury.
• Keep the working area clean and well lit.
• Keep children and non-authorized personnel away
from the working area.
• Do not operate the angle grinder if you get tired ea-
sily or under the influence of drugs, alcohol or me-
dication.
• Dress properly. Do not wear loose clothing or jewelry
and contain long hair.
• Always wear eye and respiratory protection.
• Do not operate the tool in the presence of flammable
liquid or gases.
• Do not expose the unit to rain or wet conditions.
• Make sure the switch (black rotatory knob) is in the
off position while not in use. It will prevent any da-
maged caused by an accidental connection between
red and black clamps.
• Do not connect red and black clamps directly or to
the same conductor at the same time.
• Before use, make sure the car battery and jump star-
ter selected voltage matches, and clamps are con-
nected to the correct polarities.
NOTE! Do not use the jump starter as a car battery repla-
cement and the vehicle power supply.
• Do not pull or carry the unit by its cables, and do not
pull the clamps from the battery terminals.
• Do not store the tool in wet locations or places where
temperature may exceed 50ºC.
• Have water and soap nearby in case battery acid co-
mes in contact with skin, clothing or eyes, and wash
immediately if so.

IMPORTANT REMARKS

1. The warning light (7) changes the color in different
speed as a warning for the operator:
• If the clamps are correctly connected to the battery
terminals, the light is green.
• If the clamps are connected to the battery termi-
nals incorrectly, the light will flicker in red two times
per second, and an alarm will sound.
• If the clamps are connected to a car with 24V sys-
tem and the voltage switch is in 12V position, the
light will flicker in red two times per second, and an
alarm will sound.
2. If the internal battery voltage is low, the charging sta-
tus light (3) will flicker in red.
3. The 12/24V switch (12) must be in 12V position
when recharging the jump starter. If the user turns
the switch to the "OFF" or "24V" position, the char-
ging status lights 3 and 4 will flicker in red and green,
and an alarm will sound.

OPERATION

Charging the jump starter
NOTE! Check the internal power status by pressing the
power testing button (9) and checking the voltage meter
(8) before the first use. If the red charging status light is
on, charge the unit as soon as possible.
1. Connect the charger to the power supply.
2. Connect the charger plug into the charging socket
(11).
3. The LED light (3) will turn on once the jump starter
is being charged.
4. Once the jump starter is fully charged, the LED light
(4) will be on.
5. Remove the charger from the socket and disconnect
the charger from the power supply.
12V DC output socket
You can use the jump starter to charge 12V DC applian-
ces:
1. Turn the voltage selection switch to 12 V (12).
2. Remove the cover of the 12V output socket.
· 4 ·
REF. 53688