Werbung
Installation
1 Attach the TEMPLATE on the CEILING BOARD and drill a guided hole.
2
Use a Phillips head screwdriver to detach the mount bracket from the housing.
HOUSING
MOUNT BRACKET
3 After checking the hole size to use, remove the cap and the hex nut.
CABLE HOLE CAP
HEX NUT
• Mounting combination table
When mounting camera to the housing, refer to the mounting combination table shown
below:
- A/B/C/D/E : housing assembly hole
- / / : Camera installation assembly hole
- 1/2/3 : case top number
E-
- 2
B -
- 1
B -
- 1
A-
- 1
B-
- 1
QND-6011
HCD-6010
LND-6010R
XND-6010
HCD-7010R
QND-6021
HCD-6020R
LND-6012R
XND-6020R
HCD-7010RA QND-8020R
QND-8011
LND-6011R
LND-6020R
XND-8020R
HCD-7020R
QND-8021
LND-6021R
LND-6022R
XND-8030R
HCD-7020RA
LND-6031R
LND-6030R
XND-8040R
HCD-7030R
QND-6010R
LND-6032R
HCD-7030RA
QND-6020R
QND-6012R
QND-6030R
QND-6022R
QND-7010R
QND-6032R
QND-7020R
QND-7030R
M
`
You can also scan the QR code on your product to see this mounting combination table
online.
4
Use a Phillips head screwdriver to join the mount bracket to the housing.
MOUNT BRACKET
M
`
Make sure to check the mount bracket's camera installation assembly hole and mount
assembly hole.
`
When installing the mount bracket, align the alphabet letter to the installation direction
guides of the housing before installing it.
<Camera installation assembly hole>
5 Fix the ANCHOR BOLT onto the concrete CEILING, and secure the SAFETY WIRE to the
ANCHOR BOLT as below:
1.
Tighten the NUT ("N1") on the ANCHOR BOLT.
2.
Insert the provided SAFETY BRACKET into the ANCHOR BOLT.
3.
Tighten two NUTs ("N2", " N3") onto the ANCHOR BOLT.
4.
Hook and fix one end of the SAFETY WIRE onto the SAFETY BRACKET.
5.
Hook and fix the other end of SAFETY WIRE onto the HOUSING as shown below:
ANCHOR BOLT
CEILING
A-
- 1
D -
- 2
C-
- 3
I
`
The ANCHOR BOLTs and nuts are optional and not included in the product package.
QND-8010R
XNV-6011
QNF-8010
`
ANCHOR BOLTS must be able to sustain the weight of at least 30 kg.
QNF-9010
`
If you proceed without following the instructions in the manual, that is if you work with the
QND-8030R
camera body already attached from the beginning, the safety wire could exceed its limit and
be broken when the housing is accidentally dropped, which could result in an accident.
6 Push the HOUSING inside the CEILING through the CEILING hole, and tighten the
SCREWs (x2) clockwise to fix the HOUSING on the CEILING.
(Adjust the height of the bracket to secure the housing to the ceiling.)
BRACKET
HOUSING
I
`
Using a power tool for installation could cause product damage.
If you are going to use a power tool, the torque must be 30 Nm or less.
`
Ensure that the HOUSING is firmly secured to the CEILING BOARD.
Installation direction
guides
<Housing assembly hole>
MOUNT BRACKET
HOUSING
Nut (N1)
ANCHOR BOLT
SAFETY BRACKET
Nut (N2,N3)
SAFETY WIRE
CEILING
HOUSING
BRACKET
CEILING
7
Use the provided L16 machine screws to join the camera to the mount bracket inside the
housing.
M
`
When mounting the camera, refer to the mounting combination table to select the
mounting holes appropriate to the camera size.
8
Attach the CASE TOP to the HOUSING, and tighten the 2 SCREWS on the COVER to fix it to
the HOUSING.
M
`
Refer to the mounting combination table to use the
case top appropriate to the dome cover size of the
camera.
To know the type of the case top, please check the
number marked inside.
9
Insert the SCREW CAPS into the screw holes.
SCREW CAP
TR10
HOUSING
MOUNT BRACKET
CAMERA
MACHINE SCREW
DOME COVER
CASE TOP
TR10
PT01-005755A
Werbung
