Howard Miller Nottingham Anleitungen

QUARTZ MOVEMENT AND PENDULUM INSTRUCTION
CLOCK SET UP INSTRUCTIONS
1. Move the clock close to its final location. Make sure the clock is positioned firmly on the floor. Levelers are provided
on the bottom of the cabinet. (See figure 1). WARNING: ENSURE CLOCK IS POSITIONED SQUARE AND FIRM ON THE
FLOOR SO THAT IT WILL NOT FALL OVER. ADJUST LEVELERS FOR MAXIMUM STABILITY AND PROPER ALIGNMENT.
2. Access to the clock's quartz movement, is made in two possible ways; through the front door(s), or through the upper
back access panel. If access is not possible through the front door(s), then you will need to remove the upper back access
panel. This panel was secured for shipment with retainer clips. (See Figure 2 & Figure 3) Turn the retainer clips to allow
the back access panel to slide out of the grooves. Replace this panel after set up is complete, and turn the retainer clips
to hold it in position.
3. Some clocks have decorative chains and weight shells. The chains are used to support the decorative weight shells,
and have been secured for shipment in a bag and are located directly under the quartz movement. As you remove the
chains from the bag, please notice each chain has a hook at the end. These hooks are used to hang the decorative weight
shells. (See figure 4).
WARNING: KEEP PLASTIC BAGS AND SMALL PARTS AWAY FROM CHILDREN.
QUARTZ MOVEMENT INSTRUCTIONS
1. OPERATING INSTRUCTIONS
Release the Pendulum Guide (for pendulum movements only) from the Transport-Locking Pins by gently twisting and
pulling the Pendulum Guide away from the Transport-Locking Pins. (See Figure 7) This allows the guide to hang freely.
Hang the pendulum on the Pendulum Guide. (Figure 5 & Figure 7)
Install two "C" size alkaline batteries according to the +/- symbols in the battery holders. (Figure 6)
Install two "D" size alkaline batteries for pendulum drive. (Figure 7)
2. SETTING THE TIME
Adjust the time by using the minute hand or the Time Setting knob. (Figure 6) Never turn the hour hand to set the
time; it will turn automatically with the minute hand. Turn the Time Setting knob or move the minute hand (AFTER the
batteries have been installed) so that the hands rotate clockwise. When setting the time, the clock will not chime at the
¼, ½, or ¾ hour positions.
When manually setting the time, the clock may chime a few minutes before or after the hour - this will automatically be
corrected during the first hour of normal operation. The clock may also chime out of sequence during the first hour of
operation. After setting to the correct time, it is important that the clock movement be allowed to operate for at least one
hour for the chime sequence to become fully functional. The quartz movement is highly accurate and has been adjusted
at the factory for precise time keeping.
3. CHIME MELODY
Use the switch with the symbols OFF, WEST, and MELODY2 to select the chime melody according to the following settings:
OFF = Silent
WEST = Westminster melody and full hour strike
MELODY2 = Ave Maria melody and full hour strike (Beethoven's Ode to Joy on select models)
4. VOLUME CONTROL
The volume of the chime can be modified by turning the Volume Control knob.
5. AUTOMATIC NIGHTTIME CHIME SHUT-OFF
The movement has automatic nighttime volume shut-off or volume reduction options for a period of eight (8) hours after
the switch is moved to the shut-off or volume reductions positions. This feature will automatically repeat at the same time
every 24 hours. Use the switch with the ,
= Chime silent for eight (8) hours
= Reduced volume for eight (8) hours
= Full chime volume
6. OTHER FEATURES
This movement features a 4/4 chime melody. The movement plays ¼ of the melody at quarter past the hour, ½ the
melody at half past the hour, ¾ of the melody at three-quarters past the hour, and the full melody on the hour. Following
the melody on the hour is the count hour strike. Slide the 4/4 Chime Selection switch to the 1/ position to only play the
full melody and hour strike. Slide the 4/4 Chime Selection switch to the 4/ position to play the melody at every quarter
hour as previously described.
7. BATTERY REPLACEMENT
If the clock begins to loose time, chime weakens, or pendulum stops to swing, this is the sign of weak or exhausted
batteries. Replace the batteries.
FLOOR CLOCK
, and symbols to select chime silencing according to the following settings:
FIGURE 1
FIGURA 1
FIGURE 1
ABBILDUNG 1
FIGURE 2
FIGURA 2
FIGURE 2
ABBILDUNG 2
FIGURE 3
FIGURA 3
FIGURE 3
ABBILDUNG 3
FIGURE 4
FIGURA 4
FIGURE 4
ABBILDUNG 4
FIGURE 5
FIGURA 5
FIGURE 5
ABBILDUNG 5