Howard Miller Reid Anleitungen

CLOCK SET UP INSTRUCTIONS
1. Move the clock close to its final location. Make sure the clock is positioned firmly on the floor. Levelers are provided on the
bottom of the cabinet. (See figure 1). WARNING: ENSURE CLOCK IS POSITIONED SQUARE AND FIRM ON THE FLOOR SO THAT IT
WILL NOT FALL OVER. ADJUST LEVELERS FOR MAXIMUM STABILITY AND PROPER ALIGNMENT.
2. Access to the clock's quartz movement, is made in two possible ways; through the front door(s), or through the upper back
access panel. If access is not possible through the front door(s), then you will need to remove the upper back access panel.
This panel was secured for shipment with retainer clips. (See Figure 2) Turn the retainer clips to allow the back access panel
to slide out of the grooves. Replace this panel after set up is complete, and turn the retainer clips to hold it in position.
3. Some clocks have decorative chains and weight shells. The chains are used to support the decorative weight shells, and
have been secured for shipment in a bag and are located directly under the quartz movement. As you remove the chains
from the bag, please notice each chain has a hook at the end. These hooks are used to hang the decorative weight shells.
(See figure 3).
WARNING: KEEP PLASTIC BAGS AND SMALL PARTS AWAY FROM CHILDREN.
QUARTZ MOVEMENT INSTRUCTIONS
SETTING THE TIME
1. Before inserting the batteries (Figure 6), adjust the time to 5:50 by using the Time Setting knob (Figure 6) to rotate the
hands CLOCKWISE.
2. Install alkaline batteries according to the +/- symbols in the battery holders. (Figure 6) Do not install the batteries on the
Pendulum Drive motor at this time. (Figure 7)
3. Set the time by using the Time Setting knob (Figure 6) to rotate the hands CLOCKWISE. If setting the time for PM, make sure
the hour hand passes through 12 o'clock noon until the desired time is shown. While setting the time, it is normal to hear
sounds from the movement or speaker. Continue advancing the time until the correct time is shown. Once the time is set, the
melody will adjust to the time selected, however, it is important that the clock movement be allowed to operate for at least
one hour for the chime sequence to become fully functional. The clock may chime out of sequence during the first hour of
operation. The quartz movement is highly accurate and has been adjusted at the factory for
precise time keeping.
SETTING THE MELODY (SEE FIGURE 6)
SELECT: Use the chime SELECT switch to select the chime melody according to the following settings:
4X4 WESTMINSTER = Westminster melody and Hour Strike on the hour. Additionally ¼ of the melody at quarter past the
hour, ½ the melody at half past the hour, ¾ of the melody at three-quarters past the hour, and the full melody
on the hour.
4X4 AVE MARIA = Ave Maria melody and Hour Strike on the hour. Additionally ¼ of the melody at quarter past the
hour, ½ the melody at half past the hour, ¾ of the melody at three-quarters past the hour, and the full melody on
the hour.
WESTMINSTER = Westminster melody and Hour Strike on the hour. No ¼, ½, ¾ melody during the hour.
BIM BAM = Bim Bam strike on the hour (i.e. at 1 o'clock, 1 strike of "bim-bam", at 2 o'clock then 2 strike of "bim-
bam", etc.) No melody.
VOLUME CONTROL (SEE FIGURE 6)
VOLUME: Turn the Volume Control Knob to adjust the volume.
SOUND: Use the SOUND switch to select the sound options according to the following settings:
PM11:00-AM5:45 NIGHT OFF
24 Hr ON = the chime melody and strike are always ON
OFF = the chime melody and strike are always OFF
OTHER FEATURES (SEE FIGURE 6)
MONITOR: Press the MONITOR button to demonstrate the hourly chime melody.
SET: Advances the hour strike count without advancing the time shown on the clock. Hour strike may not match
time shown on clock after pressing the SET button.
RESET: Resets the next hour strike count to 6:00AM. If after at least one hour, the hour strike count does not match the time:
- set the time to 5:50 by using the Time Setting knob to rotate the hands CLOCKWISE
- press the RESET button
- set the time to the desired time by using the Time Setting knob to rotate the hands CLOCKWISE
(If setting PM time, make sure the hour hand passes through 12 o'clock noon until the desired time is shown.)
PENDULUM SET-UP (for pendulum movements only)
1. Release the Pendulum Guide from the Transport-Locking Pin (Figure 7) by gently pushing it sideways, allowing the guide
to hang freely.
2. Hang the pendulum on the pendulum guide. (Figure 4 & Figure 7)
3. Install alkaline batteries for pendulum drive. (Figure 7)
4. Move the pendulum to the far left of center and release. (Figure 5)
5. Let the clock operate a few minutes until the pendulum settles into an even swinging motion.
BATTERY REPLACEMENT
If the clock begins to lose time, chime weakens, or pendulum stops to swing, this is the sign of weak or
exhausted batteries. Replace with new alkaline batteries.
QUARTZ MOVEMENT AND PENDULUM INSTRUCTION
= turns off the chime melody and strike from 11:00PM to 5:45AM
(Automatic Nightime volume shut-off)
FLOOR CLOCK
1
FIGURE 1
FIGURA 1
ABBILDUNG 1
FIGURE 2
FIGURA 2
ABBILDUNG 2
FIGURE 3
FIGURA 3
ABBILDUNG 3
FIGURE 4
FIGURA 4
ABBILDUNG 4
FIGURE 5
FIGURA 5
ABBILDUNG 5
495744 R4