Fan Heater - AKO H 381TLS Gebrauchsanweisung

GB
Operating Instructions

Fan Heater

1. Important Information
Keep these instructions in a safe place and pass them on to
possible future owners.
• Use device for room heating within enclosed rooms only.
• Repairs and corrective measures may only be carried out by
skilled technicians.
• Disconnect the power supply in the event of fault (pull out
the device plug or switch off the fuse).
• Do not use this device next to the bathtub, shower,
washbasin or swimming pool.
• Do not cover the heating device with any objects;
fire hazard!
• Observe the minimum clearances.
• This appliance is not intended for use by persons, including
children, with reduced physical sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
• Caution! Potential dangers can arise when the device
switches on automatically, e.g. devices which have been
covered or blocked by objects since they were last used can
cause fire.
• Caution! In order to avoid a hazard due to in advertent
resetting of the thermal cutout, this appliance must not be
supplied trough an external switching device, such as a
timer or connected to a circuit that is regularly switched on
and off by the utility.
• Do not operate the heating device in rooms where highly
flammable substances are used (e.g. solvents, etc.).
• Do not lay the connecting cable across the hot device.
2. Technical Device Description
Heat output: 2000 W
Connection voltage: 1/N~, 230-240V, 50 Hz
Dimensions in mm: (W x H x D) 246 x 236 x 183
3. Installation
The fan heater may only be used as shown, i.e. on a horizontal,
even surface. Using it on deep pile carpets is not permitted.
Please use caution when installing it in front of flammable
objects. Do not place the heating device directly below wall
sockets.
Minimum clearance in the air outlet area: 750 mm.
H 381 TLS
4. Electrical Connection
The voltage information on the type plate must match the local
mains voltage.
When the power cord of this device is damaged, it must be
replaced by the manufacturer or after-sales service or by a
similarly qualified person, in order to avoid risks.
5. Operation
The room temperature is regulated using the continuously
adjustable thermostat.
If the rotary knob is set to the smallest setting i.e. to the
extreme right (see figure), the thermostat switches the heating
device on at an ambient temperature of approx. 5° C.
Rotary knob thermostat
Using the operating mode rotary knob, two heating levels and
a cold air level can be selected. In the cold air fan operation,
turn the thermostat rotary knob to the left stop.
The indicator lamp is lit, when the device is plugged in.
Note! Rooms can become overheated if left unattended whilst
being heated; this depends on the size of the room, its heating
requirements and the setting of the thermostat. Persons who
are not able to vacate the room if the temperature becomes too
high can thus be placed in danger.
6. Protection Against Overheating
If the permissible temperature is exceeded, the fan heater
switches off automatically. When this happens, pull out the
plug and remove the cause (e.g. when the air grid is blocked or
covered). When the device has cooled sufficiently, it can be
started up again.
7. Faults
In the event of faults, please contact your electrical retailer. If
required, you can also address your queries to the service
hotline of Glen Dimplex Deutschland GmbH.
Tel.: +49 (0) 9221 709-564
Fax: +49 (0) 9221 709-589
To process your order, please state the device type as well as
its production number (E-Nr.) and manufacturing date (FD).
This information is listed on the type plate.
8. Cleaning
To clean the device, it must be disconnected from the mains
and allowed to cool down. Clean the outside of the unit using a
soft, damp cloth. Do not use scouring powder or furniture polish
as this may damage the surface. Dust which gathers inside the
device can be removed from the outside using a vacuum
cleaner.
Glen Dimplex Deutschland GmbH
Am Goldenen Feld 18, D-95326 Kulmbach
www.dimplex.de
09221709589@dimplex.de
2
Rotary knob operating mode
OFF
HIGH
COOL
WARM 50%
WARM 100%
LOW
h381-gb_ba 12/12/C