Werbung
Verfügbare Sprachen
Verfügbare Sprachen
GB
Technical Product Information BLANCOACTIS-S HD / BLANCOACTIS HD
BLANCOACTIS-S HD
Parts list BLANCOACTIS-S
1 Lever
2 Screw
3 Cap
4 Nut
5 Bush
6 Cartridge
7 Body
9 Body Support
10 Mounting set
11 Hose
12 Perlator
13 O-Ring
14 Plastic ring
15 Seal
16 Non return head
17 Nipple
18 Screw
19 Hose
20 Weight
23 Seal
BLANCOACTIS HD
Parts list BLANCOACTIS
1 Lever
2 Screw
3 Cap
4 Nut
5 Bush
6 Cartridge
7 Body
9 Body Support
10 Mounting set
11 Hose
12 Perlator
13 O-Ring
14 Plastic ring
15 Seal
Technical Data
Applications
• Pressurised hot water tank
• Thermally controlled instantaneous water heater
• Hydraulically controlled instantaneous water
heater
Operation with low pressure hot water tank (open
water heater) is not possible.
Flow pressure
• Min.
0,5 Bar
• Max.
10 Bar
• Above 5 bar, a pressure reducer must be
installed to conform to noise
class I.
Temperature
• Max. (warm water inlet)
70° C
• Recommended (energy saving) 60° C
• Tap: warm-left / cold-right
Note
Pressure differences of more than 3 bar between
cold and warm water taps must be avoided since,
otherwise, the mixing ratio of warm and cold
water can deviate significantly from that indicated
by the lever position.
Before installation and commissioning
Before the fitting is installed, the inlet pipes must
be thoroughly flushed so that no swarf, pieces of
hemp or other contaminants can enter the fitting.
Foreign bodies can enter the fitting through pipes
which have not been flushed, or the water system
in general, and damage the ceramic discs and
O-rings.
The installation of a water filter is recommended in
all cases.
Before installing the fitting, unscrew the perlator/
aerator and flush well.
Installation
ø 35 mm tap hole necessary.
Thoroughly wash all pipes to eliminate any dirt
and residue. Position the tap in the hole making
sure the seal between the tap and supporting sur-
face is in place. Fasten everything by means of
the giving nut, washer, gasket and triangular base
of reinforcement (Nr.10) if necessary.
Connect the supplying flexible hoses and giving
gaskets to the hot and cold water connections,
making sure not to twist the flexible hoses, by
keeping them steady, when screwing the nut.
Note
• Do not kink the flexible connector hoses.
• Do not strain the flexible connector hoses.
• Only screw the flexible hoses manually into the
body of the fitting. When connecting the flexible
connector hoses to the service valve or the hot
water tank, the latter must be held firmly in
place to prevent the hoses becoming twisted or
disconnected from the body of the armature.
Maintanance
Aerator cleaning
1. Unscrew the aerator (12)
2. Wash the aerator filter under running water
3. Screw again the aerator
Cartridge replacement
1. Turn off the water at the mains
2. Remove the plug, loosen the screw (2) of the
handle (1)
3. Remove the handle by pulling it
4. Loosen the threading ring (4)
5. Remove the cartridge (6) and replace it
6. Assembly in contrary sequence
Care
In order that your BLANCO kitchen fitting will pro-
vide you with years of pleasure, we recommend
wiping regularly with a dry or damp cloth. Use
clean water or a mild cleaning agent.
On no account should abrasive (neither liquid nor
powder) scouring sponges, or alcohol or acid
based cleaning agents, or other "aggressive"
cleaning agents be used.
The use of proscribed cleaning agents can dama-
ge the finish, such damage is not covered by the
guarantee.
Guarantee
If a claim is made on the guarantee, the claimant
must produce the invoice on which the date of
purchase or installation is given. We reserve the
right to make technical changes.
Werbung
