Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating Instructions
12V Distribution Socket
Item No. 2306606
Intended Use
The distribution socket serves as an extension of the built-in cigarette lighter socket in ve-
hicles such as passenger cars and motor lorries. It provides 2 additional standard sockets
(DIN ISO 4165).
Each output can provide up to 10 A current. Make sure the total current consumption of all
connected electrical load does not exceed 10 A. The distribution socket can be powered by
12 V
cigarette lighter socket.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bath-
rooms, must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged. In
addition, improper use can result in short circuits, fires, electric shocks or other hazards. Read
the instructions carefully and store them in a safe place. Make this product available to third
parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery Content
• Distribution socket
• Operating instructions
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or
scan the QR code shown. Follow the instructions on the website.
Explanation of Symbols
The symbol with the lightning in the triangle is used if there is a risk to your health,
e.g. due to an electric shock.
The symbol with the exclamation mark in the triangle is used to indicate important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
Safety Instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting per-
sonal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) General Information
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dan-
gerous playing material for children.
• Protect the appliance from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, steam and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Sufficient ventilation is essential when operating the charging unit. Never cover
the ventilating slot on the top of the housing since cooling of the unit is achieved
by convection (heat flow).
• The device should not be connected immediately after it has been brought from
an area of cold temperature to an area of warm temperature. Condensed water
might destroy the product. Wait until the device has adapted to the new ambient
temperature before use.
• Consult an expert when in doubt about the operation, safety or connection of the
appliance.
• Maintenance, modifications and repairs must only be completed by a technician
or an authorised repair centre.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
b) Connected devices
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
Operation
The vehicle cigarette lighter must be plugged into a cigarette lighter socket in the
distribution socket. The cigarette lighter socket is identified by the
the cover.
Before drilling mounting hole on the interior of the vehicle, make sure that the elec-
tric cables, brake lines, fuel tanks or similar system will not be damaged.
a) Mounting
To mount the distribution socket, slide out the mounting plate, which locate at the back of the
distribution socket. Affix it on the interior of the vehicle. The diameter of the mounting hole is
2.75 mm.
It is recommended to mount the distribution socket vertically, such that the output
sockets locate at the side.
b) Connection
Insert the universal cigarette lighter plug to the cigarette lighter socket in the vehicle. The red
LED will light up.
To avoid dust or dirt accumulate in the output sockets, only open the covers when
the sockets are in use.
c) Fuse replacement
• Disconnect the device from cigarette lighter socket in the vehicle.
• Pull out the defective fuse gently from the universal cigarette lighter plug.
• Replace the defect fuse with a new one of the same type, please refer to "Technical Data".
Care and Cleaning
• Disconnect the product from the mains before each cleaning.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
• Clean the product with a dry, fibre-free cloth.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the house-
hold waste. At the end of its service life, dispose of the product in accordance with
applicable regulatory guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the environment.
Technical Data
Input voltage ................................. 12 V
Output voltage .............................. 12 V
Output current ............................... max. 10 A (each socket)
max. 10 A (total)
Fuse .............................................. 10 A (blade type)
Dimensions (L x W x H) ................ 65 x 55 x 34 mm
Weight .......................................... 187 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in-
cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represent the technical status at the time of printing.
Copyright 2020 by Conrad Electronic SE.
symbol on
*2306606_v2_1120_02_mxs_m_en
Werbung
