Beck com.tom INDUSTRY 140.MIO16.UMTS Inbetriebnahmeanleitung

com.tom INDUSTRY 140.MIO16.UMTS
Start-up Guide
The CTI 140.MIO16.UMTS devices communicate with the com.tom
PORTAL via UMTS modem or Ethernet. The communication mech-
anism has a low data volume and can be integrated easily in exist-
ing network infrastructures.
The device may be put into service and
operated by qualified personnel only.
The device is designed for an installation on a
grounded 35 mm DIN rail in dry rooms.
The power supply of the device must be a
grounded circuit PELV (connection between
functional earth and ground). The power
supply must be a limited power source ac-
cording to the EN60950-1 chap. 2.5 or must
be provided with an anti-surge fuse of 2 A.
The digital I/Os must be protected using a
detached anti-surge fuse of 2 A.
Insert the SIM card in the device's rear before the installation on the
DIN rail. The device must be deactivated through this process.
Never use the device in areas where the operation of wireless
equipment is prohibited. The adherence of the protection against
the lightning norm VDE V 0185 is mandatory when installing the
antenna outside. The E.M.C lightning zone concept must be con-
sidered. The device must be deactivated while working with the
antenna.
Pin Assignment
Power Supplies
PIN Description
FE Functional earth
GND Ground
VCC 24 VDC
Serial Interface (COM)
Pin RS232
Pin 1 GND
Pin 2 CTS
Pin 3 -
Pin 4 Tx
Pin 5 -
Pin 6 RTS
Pin 7 -
Pin 8 Rx
CAN Interface
Pin Description
Pin 1 CAN High
Pin 2 TERM
Pin 3 CAN Low
Pin 4 TERM
RS485
GND
-
B (+/Z)
-
A (-/Y)
-
TERM_B
-
Ethernet Interfaces
Green LED Link indication
Yellow LED Activity indication
Analog and Digital I/O Configuration
Digital I/O Symbol
24V DC Supply VCCD
Input-Output 0 D0
Input-Output 1 D1
Input-Output 2 D2
Input-Output 3 D3
Input-Output 4 D4
Input-Output 5 D5
Input-Output 6 D6
Input-Output 7 D7
Ground GNDD
Status LEDs
PLC PLC status
Portal Portal status
GSM Modem status
LED 4 Freely programmable
Power Device is powered
Other Interfaces
SD card interface microSD card
USB interface Micro USB (OTG Host & Slave)
SIM card interface Mini SIM (2FF)
Antenna interface SMA connector (female)
Getting Started
Wire the com.tom device according to the technical data. Get
the appropriate
Getting
http://www.com-tom.de/start and follow the steps described
there to put your device into operation. When using the GPJ
Power Supply Connector (labeled in white), only com.tom
GRAPHIC may be connected to Port ETH1.3/GPJ.
Part Numbers
00571196 (WEB-PLC) CTI 140.MIO16.UMTS.W
00571281 (CODESYS) CTI 140.MIO16.UMTS.C
General Data
Size (W x L x H) 65 x 103 x 63 mm
Operating temperature 0 bis 55 °C
Electrical shock Class III
Protection rating IP20
EMC emission IEC 61000-6-3
EMC immunity IEC 61000-6-2
Compliance CE, RoHS
Electrical Data
Supply voltage
24 VDC (15 %)
Active current ≤ 0.20 A (without I/Os)
≤ 0.5 A per digital output
Scope of supply
1 Piece CTI 140.MIO16.UMTS
1 Piece microSD card
1 Piece Start-up guide
2 Pieces Connector 3-pin
1 Piece Connector 8-pin
1 Piece Connector 4-pin
1 Piece Connector 20-pin
Analog I
A0 Input 0
A1 Input 1
A2 Input 2
A3 Input 3
GNDA Ground
A4 Input 4
A5 Input 5
A6 Input 6
A7 Input 7
GNDA Ground
documentation at
Started
Copyright © 2018 Beck IPC GmbH
http://www.com-tom.de