Beck com.tom INDUSTRY 100.MIO12.UMTS Inbetriebnahmeanleitung

INDUSTRY 100.MIO12.UMTS
com.tom
Start-up Guide
The CTI 100.MIO12.UMTS devices communicate with the com.tom
PORTAL via UMTS modem or Ethernet. The communication mec
anism has a low data volume and can be integrated easily in exist- anism has a low data volume and can be integrated easily in exis
ing network infrastructures.
The device may be put into service and
operated by qualified personnel only.
The device is designed for an installation on a
grounded 35 mm DIN rail in dry rooms.
The power supply of the device must be a
grounded circuit PELV (connection between
functional earth and ground). The power
supply must be a limited power source ac-
cording to the EN60950-1 chap. 2.5 or must
be provided with an anti-surge fuse of 2 A.
The digital I/Os must be protected using a
detached anti-surge fuse of 2 A.
Insert the SIM card in the device's rear before the installation on the Insert the SIM card in the device's rear before the installation on the
DIN rail. The device must be deactivated through this process. DIN rail. The device must be deactivated through this process.
Never use the device in areas where the operation of wireless Never use the device in areas where the operation of wireless
equipment is prohibited. The adherence of the protection against The adherence of the protection against
the lightning norm VDE V 0185 is mandatory when the lightning norm VDE V 0185 is mandatory when installing the
antenna outside. The E.M.C lightning zone concept must be con- antenna outside. The E.M.C lightning zone concept must be co
sidered. The device must be deactivated while working with the red. The device must be deactivated while working with the
antenna.
Pin Assignment
Power Supply
PIN Description
FE Functional earth
GND Ground
VCC 24 VDC
Serial Interface (COM)
Pin RS232
Pin 1 COM_GND
Pin 2 CTS
Pin 3 -
Pin 4 Tx
Pin 5 -
Pin 6 RTS
Pin 7 -
Pin 8 Rx
CAN Interface
Pin Description
Pin 1 CAN_HIGH
Pin 2 TERM_120 ( PIN1)
Pin 3 CAN_LOW
Pin 4 TERM_GND
UMTS
with the com.tom
Ethernet. The communication mech-
RS485
COM_GND GND
-
B (+/Z)
-
A (-/Y)
-
TERM_120 120
-
Ethernet Interface
Green LED Link indication Link indication
Yellow LED Activity indication Activity indication
Analog and Digital I/O Interfaces and Digital I/O Interfaces
Digital In/Out Symbol Symbol
24V DC Supply VCCD
Input-Output 0 D0
Input-Output 1 D1
Input-Output 2 D2
Input-Output 3 D3
Temp.Sensors Symbol Symbol
RTD0.0 Chanel 0 0.0
RTD0.1 Chanel 0 0.1
RTD1.0 Chanel 1 1.0
RTD1.1 Chanel 1 1.1
Ground GNDD
Status LEDs
PLC PLC status PLC s
Portal Portal status Portal s
GSM Modem status Modem status
LED 4 Freely programmable Freely programmable
Power Device Device is powered
Other Interfaces
SD card interface microSD card micro
USB interface Micro USB (OTG Host & Slave) Micro
SIM card interface Mini Mini SIM (2FF)
Antenna interface SMA connector SMA connector (female)
Getting Started
Wire the com.tom device according to the Wire the com.tom device according to the specifications. Get
the WEB-PLC Getting Getting
http://www.com-tom.de/start and follow the steps described and follow the steps described
there to put your com.tom device into operation there to put your com.tom device into operation.
Part Numbers
00571189 (WEB-PLC) CTI 100.MIO12.UMTS.W CTI 100.MIO
00571272 (CODESYS) CTI 100.MIO12.UMTS.C CTI 100.MIO12.UMTS.C
General Data
Size (W x L x H) 46 x 103 x 63 mm
Operating temperature 0 bis 55 °C 0 bis 55 °C
Electrical shock Class III Class
Protection rating IP20 IP20
EMC emission IEC 61000 IEC 61000-6-3
EMC immunity IEC 61000 IEC 61000-6-2
Compliance CE CE, RoHS
Electrical Data
Supply voltage
24 VDC ( 24 VDC (±15 %)
Active current ≤ 0. 0.20 A (without digital I/Os)
≤ 0.5 0.5 A per digital output
Scope of supply
1 Piece CTI 100.MIO12.UMTS CTI
1 Piece microSD card microSD card
1 Piece Start-up guide Start
1 Piece Connector 3 Connector 3-pin
1 Piece Connector 8 nnector 8-pin
1 Piece Connector 4-pin Connector 4
1 Piece Connector 20 Connector 20-pin
1 Piece Label MAC Label MAC-ID
Analog In
A0 Input 0
A1 Input 1
A2 Input 2
A3 Input 3
GNDA Ground
Analog Out
GNDA Ground
AO.0 Output 0
GNDA Ground
AO.1 Output 1
GNDA Ground
Started Started documentation at
Copyright © 2018 Beck IPC GmbH
http://www.com-tom.de