Time Settings; Language; Factory Reset; Software Update - Loewe klang s1 Benutzerhandbuch

Loewe klang s1/s3

Time settings | Language | Factory reset | Software update | Setup wizard | Info
Privacy policy | Backlight | Ambient light | Loewe radio - control of the radio via App
21

Time settings

Settings for time and date can be made in the
[Time/Date] menu. The following options are
available:
21.1 [Set Time/Date] menu
In this menu you can set the time and date ma-
nually. The values can be changed using the
or button. Use the OK button to save the va-
lue. After saving a value, next block of numbers
will be automatically selected. Repeat previous
steps to set all values for date and time.
21.2 [Auto Update] menu
Here you can specify the source from which the
time and date should be updated. The following
options are available:
[Update from DAB]: Time and date are up-
dated via DAB.
[Update from FM]: The time and date are
updated via FM.
[Update from Network]: The network updates
the time and date.
[No update]: Time and date must be set
manually.
The currently selected option is marked with [*].
21.3 [Set format] menu
In this menu you can specify whether the clock
should be displayed in 12 or 24 hour format.
Select desired option with the
confirm with the OK button. The currently se-
lected option is marked with [*].
21.4 [Set timezone] menu
In this menu you can specify your time zone.
Select desired time zone with the
button. Confirm selection with the OK button.
The currently selected option is marked with [*].
21.5 [Daylight savings] menu
In this menu you can turn on or off the daylight
savings time. Select desired option with the
button. Confirm selection with the OK
or
button. The currently selected option is marked
with [*].

22 Language

In the [Language] menu you can set the menu
language of the radio. If you have started up
the device with the Setup wizard, the device
language has already been set there. To select
a language, please use the or
confirm this by pressing the OK button.
The following languages are available:
Danish, German, English, Finnish, French, Italian,
Dutch, Norwegian, Polish, Portuguese, Swedish,
Spanish, Turkish.
26

23 Factory reset

To reset the radio to the delivery state, please
select [YES] in the menu [Factory reset].
Attention: All previous settings are deleted.
If you select [NO] the process is cancelled.
Note: In any case, reset the radio to the delivery
state before you pass it on (e.g. sell, give away
or disposal).

24 Software update

In this menu you can check whether a software
update is available for the radio.
If you select [Auto-check setting] the radio
automatically checks the availability of new
software updates on a regular basis.
Select the menu item [Check now] to search
for a new version. If newer software is found,
please select [YES] to install it or [NO] to cancel
the update. If [YES] the radio restarts to carry
out the process.
Then the software is downloaded and you are
asked with [Proceed] whether the update
should be carried out. Please choose [YES] if
you consent or [NO] to cancel the update. The
[Warning: do not remove power] and the
software version to be installed flash alterna-
tely. When the process is complete, [Update
completed] appears on the display and you
can confirm the process with the OK button.
You can check the version number of the in-
or button,
stalled software under the [System settings]
menu under [Info].
Attention!
Make sure that there is a stable power supply
before you start a software update.
or
An interruption during an update can cause
irreparable damage to the radio!

25 Setup wizard

You can start the setup wizard again in the [Set-
up wizard] menu. To do this, proceed as descri-
bed under "Starting the setup wizard" chapter.

26 Info

In this menu you will find the version number
of the current firmware, among other things.
Have this ready if you want to contact customer
service.
buttons and
27

Privacy policy

Please read the data protection regulations
listed on this website:
privacy-klang.loewe.tv

28 Backlight

The display illumination can be programmed in
3 brightness levels. The following settings can
be made in the [Backlight] menu:
[Timeout]: Time until the display is set to the
[Dim level] lighting level.
Choices: [On / 10 / 20 / 30 / 45 / 60 / 90
/ 120 / 180 seconds]
[ON] means that the radio always remains in
the brightness level of the [On level].
[On level]: Brightness of the display when the
radio is switched on. Choices: [High] / [Me-
dium] / [Low]
[Dim level]: Brightness adjustment for opera-
tion and standby. Choices: [Medium] / [Low]
29 Ambient light
The [Ambient light] menu controls the illu-
mination of the volume knob when the radio is
turned on. You can change the light intensity by
selecting one of the following options: [High] /
[Medium] / [Low] / [Off]
30 Loewe radio - control
of the radio via App
The "Loewe radio" application (App) developed
by Frontier Silicon gives you full control of radio
on your smartphone.
Regardless of whether you are setting up the
device for the first time, configuring Equalizer
or managing your favourite channels - "Loewe
radio" offers you all the features on your smart-
phone or tablet and offers you even more con-
venience. Download the "Loewe radio" App from
the Google Play Store or the Apple App Store.
30.1 Initial setup of the device
with "Loewe radio"
When switched on for the first time, or after the
radio has been set to the factory settings, the
radio is in SETUP mode and a so-called micro-
access point (own WLAN network) is generated.
This allows your smartphone or tablet to con-
nect to the radio.
30.2 Set up with Android
Make sure the radio is in SETUP mode. Open
the "Loewe radio" App on your smartphone
or tablet and select the menu item [SET UP
AUDIO SYSTEM].
Press [NEXT] and select the menu item
[CHOOSE ACCESS POINT].