Maintenance Instructions; Functional Description; Overload Protection - Makita UD2500 Original Bedienungsanleitung

• Do not tilt the machine during operation.
• Keep abundant distance when you put long material. It
may spring back and may result in personal injury.
• Do not operate without the filling hopper.
• Do not force the machine. It does the job better and
safer at the rate for which it was designed. Frequent
overload may cause motor damage or fire.
• Use the right appliance. Do not use appliances for pur-
poses not intended. Never intend to feed metal parts,
glasses, stones, ceramics, plastics, thicker branches,
hard wood or thick wood plates, etc.

Maintenance instructions

• Have your machine serviced by our authorized service
center, always using only genuine replacement parts.
Incorrect repair and poor maintenance can shorten the
life of the machine and increase the risk of accidents.
• Before servicing, inspection, adjustment, storage, or to
change an accessory, take following steps:
– Shut off the power source
– Disconnect the machine from power supply
– Make sure that all moving parts have come to a
complete stop
– Allow the machine to cool.
• Inspect on the machine for possible damage:
– Whether safety devices works properly for its
intended function
– Whether all the moving parts work smoothly and
adequately
– Whether all parts are not damaged and properly
installed
– Replace or repair by our authorized service
center if there are any damaged parts.
• Pay extreme attention when servicing cutter. The cutter
is able to move manually tough interlock feature of the
guard functions.
• Do not clean the device with water. It may cause electri-
cal shock.
• Wear protective gloves during maintenance or assem-
bly work to prevent injury to fingers.
• Do not carry out maintenance or repair work other than
that described in this instruction manual. Any other
work must be carried out by Makita aurhorized service
center.
• Only use original Makita replacement parts and ac-
cessories intended for your machine. Otherwise it may
result in personal injury or damage on the machine.
• Store the machine in a dry room. Keep it out of reach of
children. Never store the machine outdoors.
ASSEMBLY
CAUTION:
• Always be sure that the machine is switched off and
unplugged before carrying out any work on the tool.
1. Place the upper enclosure upside down on the flat
floor. And then put the base frame on it. Be careful
about the direction of the part. (Fig. 2)
2. Fasten each part by tightening screws. Make sure they
become perfectly stable. (Fig. 3)
3. Attach the stoppers by screw. Make sure they are
fastened tightly. (Fig. 4)
8
4. Attach wheels as follows: (Fig. 5)
– Attach the axis on one of the wheel.
– Pass the axis through the holes on the leg.
– Attach the other wheel to the axis by passing
the pin through the hole on the axis. Fasten the
wheel by bending the pin.
– Attach the covers on the wheels.
5. Attach the retaining basket. And then raise the lock
lever. (Fig. 6)

FUNCTIONAL DESCRIPTION

WARNING:
Before plugging the machine, always make sure that the
machine is switched off. Plugging the machine with the
switch on may cause an unexpected start resulting in
serious personal injury.
Power Switch (Fig. 7)
CAUTION:
Do not use the machine if the switch does not turn it on
and off. Have defective switches replaced by Makita
authorized service center.
To turn on the machine, push the green button.
To turn off the machine, push the red button.
LED light
The LED light indicates the status of the machine as
follows:
RED color: When the machine is connected to the
power supply and the machine is switched off.
GREEN color: When machine is switched on.
Flickering GREEN color constantly: When the
machine is blocked during operation.
Flickering RED color: When the machine can not
recover automatically. Clear the problem manually
when it happens.
Unintentional restart proof
The machine switches off automatically when power
failure happens. To restart, push the green button again.

Overload protection

The motor is equipped with an overload protection. When
overloaded, the machine acts as follows:
– The blade runs reverse for two or three seconds
to try to push the shredded material back out.
– The blade runs forward again.
– If the material is still clogged after this attempt
for three times, the machine stops with LED light
flickering in red.
When it happens perform the following steps:
– Turn off the machine.
– Wait until the blades stop completely.
– Remove the clogged material.
– Turn the shredder on again after about 5 minutes,
and feed easier material.
– If you cannot turn on the machine after this
waiting time, refer to "Trouble shooting".