Maintenance - Honeywell HS10S Installationsanleitung

7.3 Discharge of reverse rinsing water
The reverse rinsing water must be routed to the drain channel
in such a way that no backwater can occur.
To do this there are 3 options:
1. Direct connection:
o Connector DN 50/70 as well as the necessary pipes and
siphon (3 elbows 90°) in DN 70.
2. Drain free to existing floor drain.
3. Drain into open container.
Filter size Reverse rinsing volume*
1/2" and 3/4" 12 litres
1" and 1 1/4" 15 litres
1 1/2" and 2" 18 litres
*at 4 bar inlet pressure and 3 x 3 seconds reverse rinsing
duration
8. Commissioning
8.1 Setting outlet pressure
Set outlet pressure min. 1 bar under inlet pressure.
1. Close shutoff valve on inlet
2. Release pressure on outlet side (e.g. through water tap)
3. Close shutoff valve on outlet
4. Loosen slotted screw
o Do not remove slotted screw
5. Slacken tension in compression spring
o Turn control handle to the left (-) until it does not move
any more
6. Slowly open shutoff valve on inlet
7. Retighten slotted screw
8. Slowly open shutoff valve on outlet
9. Turn control handle until the setting scale shows the
desired value
8.2 Reverse rinsing
During reverse rinsing, an inlet pressure of at least 1.5 bar is
required. The reverse rinsing interval depends on the degree
of dirt in the water. At the latest every 2 months, reverse
rinsing should be carried out according to DIN 1988, Part 8.
To ensure convenient and regular adherence to the reverse
rinsing interval, we recommend installing an automated
reverse rinsing system Z11S.
Filtered water can also be tapped during reverse
rinsing.
MU1H-1101GE23 R0507
All manuals and user guides at all-guides.com
GB
8.2.1 Manual reverse rinsing
If reverse rinsing water is not to be discharged via a direct
connection, a collecting container must be positioned
beneath before reverse rinsing.
1. Open ball valve by turning the reverse rinsing button to the
2. Close ball valve again after approx. 3 seconds. Repeat
With aid of the memory ring, the next deadline for manual
reverse rinsing can be booked.
8.2.2 Automatic reverse rinsing with the Z11S
The automated reverse rinsing system Z11S is available as
an accessory. The automated system reliably takes over
reverse rinsing of the filter at intervals which can be set
between 4 minutes and 3 months.

9. Maintenance

In accordance with DIN 1988, part 8, the following measures
must be taken:
9.1 Inspection
9.1.1 Pressure reducing valve
1. Close shut off valve on outlet
2. Check back pressure using a pressure meter when there
3. Slowly open shutoff valve on outlet
9.1.2 Filter
• The filter must be cleaned by reverse rinsing regularly, at
• Non-compliance can lead to the filter becoming blocked
• The filter meshes are made of stainless steel. A red
8
stop point
o Select bar must be upright
o The patented reverse rinsing system starts
o When filtering with Double Spin Technology, a visual
function check is possible through the rotating red rotor
procedure three times
o If the filter is extremely dirty, the procedure may have to
be repeated additional times
We recommend a planned maintenance contract
with an installation company
Interval: once a year
is zero through-flow
o If the pressure is increasing slowly, the valve may be
dirty or defective. In this instance, carry out servicing and
cleaning
Interval: every 2 months
the latest every 2 months
This results in a drop in pressure and decreasing water
flow
coating as a consequence of rust from the pipelines has no
influence on function or the way the filter works
Do not forget to do a visual check of the ball valve.
Replace if it is dripping!
Honeywell GmbH