Herunterladen Diese Seite drucken

Wieland wipos PB1 24-4.2 Montageanleitung Seite 2

Werbung

Montageanleitung (Original) / Installation instruction (translation from original)
wipos PB1 24-4.2
Schaltnetzgeräte für Hutschienenmontage / DIN rail mountable switching power supplies
3
Montage
Zulässige Montagelage und Abstände: Siehe Bild 1. Die Belüftungsöffnungen müssen mit
dem angegebenen Abstand für die Kühlung freigehalten werden.
Anbringen auf Trägerschiene (siehe Bild 2)
1. Kippen Sie das Gerät etwas nach hinten.
2. Haken Sie das Gerät oben auf der Schiene ein.
3. Drücken Sie das Gerät nach unten und gegen die Schiene, bis es einrastet.
4. Prüfen Sie, ob das Gerät fest auf der Tragschiene sitzt.
Verdrahtung (siehe Bild 3)
Verwenden Sie nur Kupferleitungen!
Temperatur-Einstufung nach UL 508: 60/75 °C
Maximal zulässige Umgebungstemperatur nach UL 508: 50 °C
Zulässige Lasten, Kabelquerschnitte und Abisolierlängen: Siehe Technische Daten.
Verwenden Sie nur handelsübliche Leitungen, die für die angegebenen Spannungs- und
Stromwerte zugelassen sind!
Bei mehradrigen Leitungen: Vermeiden Sie das Aufspleißen von Einzeldrähten!
Stellen Sie die richtige Polung der Ausgänge sicher!
Interne Sicherung
Die interne Eingangssicherung schützt das Gerät und darf vom Anwender nicht ausge-
tauscht werden. Im Falle eines Gerätedefektes muss das Gerät aus Sicherheitsgründen an
den Hersteller geschickt werden.
4
Demontage (siehe Bild 4)
WAR NUNG
Schalten Sie die Spannungsversorgung aus und trennen Sie das Gerät vom Netz.
Führen Sie einen flachen Schraubendreher in den Schlitz der Zunge. Hebeln Sie die Zunge
nach unten, bis sie klickt, und kippen Sie das Gerät nach oben.
5
Technische Daten
Wenn nicht anders angegeben, gelten alle Angaben für U
Bemessungsleistung
100,8 W
Bemessungsausgangspannung U
24 V DC
OUT
Bemessungsausgangsstrom I
4,2 A
OUT
Einschaltstrom 115 V AC / 230 V AC
30 A max. / 60 A max.
Einstellbereich Ausgangsspannung
24 ... 28 V
LED "DC OK" an bei ca.
<19,2 V
Wirkungsgrad [typ.]
89%
Allgemeine Angaben
Trennspannung (Ein- / Ausgang)
3000 V AC / 4242 V DC
Trennwiderstand
100 MΩ
Umgebungstemperatur
-40 ... +71 °C
UL
max. 50 °C
Lagertemperatur
-40 ... +85 °C
Derating
+61 ... +71 °C (siehe Bild 6)
Relative Feuchte
20 ... 95%, keine Betauung
Temperaturkoeffizient
±0,03% / °C
Kühlung
Freie Konvektion
Betriebshöhe
5000 m
MTBF
554.000 h
Verschmutzungsgrad
2
Schutzart
IP20
Schutzklasse
II bei bestimmungsgemäßer Montage
Abmessungen H × B × T
91 × 90 × 57 mm
Gewicht
380 g
Gehäusematerial
Kunststoff (Polycarbonat)
Anschlüsse
Leitergröße AWG
24 – 12 ein-/mehrdrähtig
Anschlussvermögen
0,2 – 2,5 mm² ein-/feindrähtig
Abisolierlänge
7 mm
Drehmoment
max. 0,7 Nm
Eingänge ("N", "L")
Bemessungsspannung
100 ... 240 V AC
Spannungsbereich
90 ... 264 V AC / 120 ... 375 V DC
Netzfrequenz
47 ... 63 Hz
Eingangsstrom
max. 2,2 A
Ausgänge ("+", "–")
Spannungsgenauigkeit
-0%, +1%
Netzregelung
±1%
Lastschwankung
±1%
Welligkeit und Rauschen
<50 mV
Verweilzeit
115 V AC
>10 ms
230 V AC
>60 ms
Überwachung und Schutz
Interne Sicherung Eingang
T3.15A / 250 V AC
Kurzschluss Ausgang
Fold forward
Überlast Ausgang
110 ... 150%
Normen und Zulassungen
CE, cULus, cURus
Doc. # BA000651 – 04/2021 (Rev. C)
81.000.6340.0
und I
bei 25 °C.
OUT
OUT
SS
Wieland Electric GmbH
Brennerstraße 10 – 14
96052 Bamberg
Phone +49 951 9324-0
Fax
+49 951 9324-198
info@wieland-electric.com
www.wieland-electric.com
3
Installation
Permissible mounting position: see fig. 1. Keep free ventilation hole, leave space for cooling!
Recommended to have 25 mm free space at all sides for ventilation and cooling.
Snap on DIN rail (see fig. 2)
1. Tilt the unit slightly backwards.
2. Fit the unit over top hat rail.
3. Push downwards and against the rail for locking.
4. Check that the unit is locked into position.
Wiring (see fig. 3)
Use copper conductors only!
Temperature rating acc. to UL 508: 60/75 °C
Maximum surrounding air temperature acc. to UL 508: 50 °C
Permitted loads, cable cross-sections and stripping: See Technical data.
Use only commercial cables designed for the indicated voltage and current values!
With flexible cables: Avoid fanning of strands!
Ensure proper polarity at output terminals!
Internal fuse
The internal input fuse serves to protect the unit and must not be replaced by the user. In
case of an internal defect, the unit must be returned to the manufacturer for safety reasons.
4
Removal from DIN rail (see fig. 4)
Switch mains power off and disconnect your system from the supply network.
Insert a flat screwdriver into the slot in the clamp. Push down the clamp until it clicks, and
tilt the unit upwards.
5
Technical data
All specifications are typical at V
Rated output power
Rated output voltage V
OUT
Rated output current I
OUT
Inrush current typ. 115 V AC / 230 V AC 30 A max. / 60 A max.
Output voltage trim range
LED 'DC OK' on at (approx.)
Efficiency [typ.]
General specification
Isolation (input / output)
Isolation resistance
Operation amb. temperature
Storage temperature
Derating
Relative humidity
Temperature coefficient
Cooling
Altitude during operation
MTBF
Degree of pollution
IP rating
Safety class
Dimension H × W × D
Weight
Case material
Connections
Conductor size AWG
Rated conductor size
Conductor strip length
Torque
Input specification ('N', 'L')
Rated input voltage
Input voltage range
Line frequency
Input current
Output specification ('+', '–')
Output voltage accuracy
Line regulation
Load regulation
Ripple & Noise
Hold up time
115 V AC
230 V AC
Control and protection
Input internal fuse
Output short circuit
Output overload
Approvals and standards
wipos PB1 24-4.2
WAR NING
, I
and 25 °C, unless otherwise noticed.
OUT
OUT
100.8 W
24 V DC
4.2 A
24 ... 28 V
<19.2 V
89%
3000 V AC / 4242 V DC
100 MΩ
-40 ... +71 °C
UL
max. 50 °C
-40 ... +85 °C
+61 ... +71 °C (see fig. 6)
20 ... 95%, non-condensing
±0.03% / °C
Free air convection
5000 m
554,000 h
2
IP20
II if mounted according to specifications
91 × 90 × 57 mm
380 g
plastic (polycarbonate)
24 – 12 solid/stranded
0.2 – 2.5 mm² solid/fine-stranded
7 mm
max. 0.7 Nm (6.0 lb-in)
100 ... 240 V AC
90 ... 264 V AC / 120 ... 375 V DC
47 ... 63 Hz
max. 2.2 A
-0%, +1%
±1%
±1%
<50 mV
PP
>10 ms
>60 ms
T3.15A / 250 V AC
Fold forward
110 ... 150%
CE, cULus, cURus
2 DE / EN

Werbung

loading