Werbung
Verfügbare Sprachen
Verfügbare Sprachen
SHOTGUN MICROPHONE
Condenser microphone with ball joint
The MSM PRO series was designed for live sound reinforcemant and
broadcasting and in studio or live recording. The microphone operates on
16-52 V phantom power. A foam windscreen is included in the delivery.
Safety Instructions
Maintenance and service operations are only to be carried out by authorized
dealers. Damage, caused by manual modifications on the microphone are
not subject to warranty. If the microphone is used for other purposes than
originally intended or if it is not correctly connected, the product may suffer
damages and the guarantee becomes void.
Maintenance
We recommend a frequent cleaning of the device. Please use a soft lint-free
and moistened cloth. Never use alcohol or solvents!
Setting into Operation
Place the supplied windscreen on the microphone.
Insert the microphone into the XLR microphone input of the audio unit (e. g.
mixer or amplifier). The microphone input must provide phantom power
(16-52 V). Adjust the microphone to the sound source, speaker or instrument.
Technical Specifications
Type:
Condenser (back electret)
Operating principle:
Pressure gradient
Polar pattern:
Line + gradient
Frequency range:
50 - 18,000 Hz
Sensitivity at 1 kHz:
10 mV/Pa; -36 dBu (± 3 dB/Pa)
Nominal impedance:
250 Ohm ± 30%
1250 Ohm ± 30%
Load impedance:
Max. SPL:
135 dB (THD < 0.5% @ 1 kHz)
S/N ratio:
72 dB
Equivalent SPL:
21 dBA
Dynamic:
113 dB
Power supply:
16 V - 52 V DC phantom power
Current consumption:
3.5 mA
Connection:
3-pin XLR
Dimensions (LxWxH):
19 x 19 x 238 mm
Weight:
250 g
Please note: Every information is subject to change without prior notice. 28.11.2006 ©
© Copyright
Nachdruck verboten!
Reproduction prohibited!
1: Ground
2
1
2: In Phase (+)
3
3: Out of Phase (-)
13030834_V_1_0.DOC
www.omnitronic.com
SHOTGUN MICROPHONE
Condenser microphone with ball joint
The MSM PRO series was designed for live sound reinforcemant and
broadcasting and in studio or live recording. The microphone operates on
16-52 V phantom power. A foam windscreen is included in the delivery.
Safety Instructions
Maintenance and service operations are only to be carried out by authorized
dealers. Damage, caused by manual modifications on the microphone are
not subject to warranty. If the microphone is used for other purposes than
originally intended or if it is not correctly connected, the product may suffer
damages and the guarantee becomes void.
Maintenance
We recommend a frequent cleaning of the device. Please use a soft lint-free
and moistened cloth. Never use alcohol or solvents!
Setting into Operation
Place the supplied windscreen on the microphone.
Insert the microphone into the XLR microphone input of the audio unit (e. g.
mixer or amplifier). The microphone input must provide phantom power
(16-52 V). Adjust the microphone to the sound source, speaker or instrument.
Technical Specifications
Type:
Condenser (back electret)
Operating principle:
Pressure gradient
Polar pattern:
Line + gradient
Frequency range:
50 - 18,000 Hz
Sensitivity at 1 kHz:
10 mV/Pa; -36 dBu (± 3 dB/Pa)
Nominal impedance:
250 Ohm ± 30%
1250 Ohm ± 30%
Load impedance:
Max. SPL:
135 dB (THD < 0.5% @ 1 kHz)
S/N ratio:
72 dB
Equivalent SPL:
21 dBA
Dynamic:
113 dB
Power supply:
16 V - 52 V DC phantom power
Current consumption:
3.5 mA
Connection:
3-pin XLR
Dimensions (LxWxH):
19 x 19 x 238 mm
Weight:
250 g
Please note: Every information is subject to change without prior notice. 28.11.2006 ©
©
Copyright
Nachdruck verboten!
Reproduction prohibited!
1: Ground
2
1
2: In Phase (+)
3
3: Out of Phase (-)
13030834_V_1_0.DOC
www.omnitronic.com
Werbung
