Care And Maintenance - KIKKA BOO I AM SAFE Gebrauchsanweisung

WARNINGS
• This product is available in two di erent sizes 102cm or 150cm, depending on your purchase.
• Before installing or using this bedrail you have to read the instructions with care. If you do not follow the instruction, your child can risque some
danger situations!
• This bedrail may not be installed onto beds where the sleeping level is situated 60 cm or higher from the oor.
• The bedrail may not be installed on in atable beds or in babycots.
• For avoiding all risques there must be a space of 25 cm between the side of the barrière and the front of the bed, or other parts of the bed.
• Do not use this bedrail in stead of a babycot, the bedrail does not give the same level of security.
Instruction for use:
• Check carefully if all spare parts are present.
• When some spare parts are missing or broken, do not continue to assemble but contact your salespoint for assistance.
• Take the matress of the bed and place the bedrail on the matress oor. Make sure there will be a minimum space of 25 cm between the front of
the bedrail and each headend of the bed.
• Fix the the bedrail in such way that there is as less space as possible between the bedrail and the matress.
• Now x the bedrail with the screws (H) (See drawing 4)
• Control if the bedrail is xed well and put the matress back to its position.
• Attention: the distance between the top of the bedrail and the matress may not be less than 16cm. If the distance is less than 16 cm you have
to adjust the thickness of your matress.
• Control on regularely basis if the bedrail is still tightened and if the matress have not been moved away from the bedrail.
• In case any parts get damaged, missing or broken please contact your salespoint for further assistance.
• Do not install the gate if parts are missing or damaged.
• Use replacement parts and accessories from the same manufacturer only.
• Regularly check the soundness of screws and the construction.
• Do not place objects such as chairs or waste bins near the stair gate.
• Wrong and incorrect installation can be dangerous.
I. PRODUCT COMPONENTS
1.1. PARTS; 1.2. PRODUCT VIEW
1.3. NOTES: Place all parts in correct order ready for installation. Please note points 2 & 3 for reference, note one end of the bar is larger than the
opposite when installing.
II. ASSEMBLY
2.1. Connect the top section of the bedrail together and slide carefully through the fabric.
2.2. Connect the first leg uprigh. Note: once connected, pull the fabric carefully down over the hinge. Repeat the process on the opposite side.
2.3. Connect the bottom rail together before sliding through the fabric. ake sure the parts with mark C+D are connected together. Connect the
small end first, then at the opposite side pull back the plastic connector and slide over the larger end, and connect in place.
2.4. Installing the bedrail, there are two methods of installation. Method 1: Lift the mattress off the bed, position the bed rail, and screw directly
into the bed base or lath securing the bed rail in place. Method 2: Use the bedrail tethers provided, using the hooped end, slide over the bedrail leg
upright, lay the tether across the beds base and place the mattress. ake sure the steel plate on the tether is upright against the mattress and
adjust the tether to suit the beds width making sure the bedrail is secure and tight against the mattress.
2.5. Installation complete.
2.6. To lower the bedrail, depress both buttons at the same time located at either end of the bedrail hinge, and lower.
III. CARE AND MAINTENANCE
Fabric parts: 1. The fabrics must be cleaned with warm water and mild soap. After cleaning let get completely dry before you use it. If is absolutely
forbidden to fold it and store it before it is completely dry.
2. Do not use strong cleaning agents, bleach or agents with abrasive particles, in order to clean the product. It is forbidden to clean it in a washing
machine, dryer, dry cleaning, bleach and tumble-dry it.
Plastic and metal parts : 1. The plastic and metal parts must be cleaned with a damp soft cloth and dried with dry soft cloth.
2. Do not let the product exposed to the harmful effect of external factors - direct sunlight, rain, snow or wind. This may lead to damage of the
metal and plastic parts and fading of the fabrics.
3. When you are not using the product, store it at a dry and well ventilated place, not in dusty, humid premises with very high or very low room
temperatures.
ENGLISH