Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating Instructions
Metal stopwatch
Item No. 2306490
Intended use
This product is a highly precise and full-featured electronic stopwatch with a clear display. Its
intended use is for sports training, competition activities, scientific research, education, and
military and industrial applications.
The unit cannot be used or stored in extreme heat or freezing conditions and rough use may
result in damage to the stopwatch. The unit should be stored in a dry environment when not
in use.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described, the product may be damaged. In addition,
improper use can result in hazards. Read the instructions carefully and store them in a safe
place. Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Stopwatch (CR2032 battery included and installed)
• Lanyard
• Operating instructions
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/downloads or
scan the QR code shown. Follow the instructions on the website.
Explanation of symbols
The symbol with the lightning in the triangle is used if there is a risk to your health,
e.g. due to an electric shock.
The symbol with the exclamation mark in the triangle is used to indicate important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting per-
sonal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) General information
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave the packaging material lying around carelessly. This may be
dangerous for children to play with.
• Protect the appliance from extreme temperatures, direct sunlight, strong jolts,
high humidity, moisture, flammable gases, steam, and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- Is visibly damaged,
- Is no longer working properly,
- Has been stored for extended periods in poor ambient conditions, or
- Has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts, or a fall, even from a low
height, can cause damage to the product.
• Consult an expert when in doubt about the operation, safety, or connection of
the appliance.
• Maintenance, modifications, and repairs must only be completed by a technician
or an authorised repair centre.
• If you have questions that remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
Caution:
• To avoid damaging the components, do not attempt to open or repair the PCB
without professional guidance.
• The operating range may be affected by environmental factors and nearby
sources of interference.
• Proper use helps to prolong the lifespan of the product.
b) Batteries
• Correct polarity must be observed while inserting the battery.
• The battery should be removed from the device if it is not used for a long period of
time to avoid damage through leaking. Leaking or damaged batteries may cause
acid burns when in contact with skin, therefore use suitable protective gloves to
handle damaged batteries.
• Batteries must be kept out of reach of children. Do not leave batteries lying
around, as there is a risk that children or pets may swallow them.
• Batteries must not be dismantled, short-circuited or thrown into fire. Never
recharge non-rechargeable batteries. This may cause an explosion!
Operating elements
S2
S3
S1 Start/stop/adjust
S3 Display by segments/
renew/set
S2 Cycle/select
Features
• The range of stopwatch time measurements is 0.01 (1/100) seconds to 9 hours, 59 minutes
and 59.99 seconds.
• The display can show the time segment, total time, number of segments, accumulative
time, slowest and fastest average time, and 10-lap memory information.
• The countdown timer can be set to start at any time in the measurement range (between 9
hours, 59 minutes and 59.99 seconds and 0.01 seconds) and then countdown to 0 seconds.
• The metronome tempos include 10, 20, 30, 40, 60, 80, 100, 120, 180, 240 and 320 beats
per minute.
• The clock displays hours, minutes, seconds, months, days, weeks and years, and supports
12- and 24-hour time formats.
• Up to four alarms can be set, with the alarm lasting for 30 seconds.
Operation
When turning on the stopwatch, the time is initially displayed. Press the S4 (Mode) key to toggle
between the following modes:
1. Clock
• The upper row of information displays the week, month, day and year, while the lower row
displays A (for AM) or P (for PM) if in 12-hour time format and the time in hours, minutes
and seconds.
• To adjust the year, month, day, 12/24-hour time format or time, press the S3 key to toggle to
the desired item. Then press the S1 key to adjust the value and press the S3 key to confirm
the change. Note that the first row displays the week number in Arabic numerals, which is
automatically adjusted based on the date and so cannot be adjusted directly.
2. Stopwatch
• Press the S1 key to start the stopwatch timer. The displayed upper value is initially zero and
the lower value is the timer. Press the S1 key to stop the timer (displaying STOP on the
screen) and then press the S1 key again to re-commence the timer. Press the S1 to stop
the time first, and then press the S3 key to return the time to zero.
• While timing, press and hold the S3 key to display the first recorded time on the upper row
and the total time on the lower row. Then release the S3 key to continue displaying the first
recorded time on the upper row and the continuing timer on the lower row. This process can
be repeated for each recorded time for up to the maximum time range (9 hours, 59 minutes
and 59.99 seconds).
S1
S4
S4 Mode toggle
Werbung
