Set Up; Connect Power; Power On/ Standby Mode; Setting The Clock Time Using The Auto-Sync Clock Feature - Honeywell OVALE OVD270 Bedienungsanleitung

SET UP

Connect Power

SECTION
Insert plug
1. Three Interchangeable Power Adapter Plugs are included
with the AC Power Adapter. Choose the correct plug type
for your region.
Insert the plug into the AC Power Adapter and lock into
place.
Lightning Dock
Cover
2. Connect the AC Power Adapter Cable into the DC Jack on
the back of the Ovale
3. Plug the AC Power Adapter into an available AC Electrical
Outlet.
4. The LED Display Screen will glow when the power has
been connected correctly.

Power On/ Standby Mode

1. Press the
Docking Speaker. The speaker and the LED Display
Screen will automatically switch to the last selected Audio
Source Mode.
2. Press and hold the
switch the speaker "OFF" to Standby Mode. In Standby
Mode, the entire unit switches off and only the clock time
will appear on the LED Display Screen.
IMPORTANT: Unplug the AC Power Adapter to completely
switch off the speaker and Clock Display Screen. All Clock
and Alarm Clock settings will be forgotten and must be
reset upon reconnecting the power to the speaker.
Setting the Clock Time
12 Hour Display
PM
Indicator
Light
Downloaded from www.Manualslib.com
3 Interchangeable Power
Release plug
Push
AC Power Adapter
(Plug into AC Electrical Outlet)
AC Power Adapter Cable
(Plug into DC Jack)
Wireless Docking Speaker.
™
Button to switch ON the Ovale
Button for about 2 seconds to
24 Hour Display
manuals search engine
SET UP (CONTINUED)
Setting the Clock Time using the Auto-Sync Clock
Feature
Adapter Plugs
1. Push
2. Pull
1. Make sure the Docking Speaker is in Standby Mode and
the clock time has not yet been set.
2.
Lift the Lightning Dock Cover and gently place the iPod/
iPhone/ iPad onto the Lightning Dock Connector. Insert
the iPad Stand behind the Lightning Dock Connector
when docking an iPad.
IMPORTANT: You must remove any external iPod/
iPhone/ iPad case before docking the device onto the
Docking Speaker.
3. Dock your iPod/ iPhone/ iPad onto the the Docking
Speaker and wait for about 10 seconds.
4. The time on the LED Display Screen will automatically
match the time on your iPod/ iPhone/ iPad.
IMPORTANT: Since the clock synchronizes with the time
AC Electrical Outlet
on your iPod/ iPhone/ iPad, you should make sure the
time on your device is correct before setting up the time
using the Auto-Sync Clock feature.
IMPORTANT: After you have performed the auto-sync
procedure the first time, the Docking Speaker will not
auto-sync the time with other devices that are docked
later. The time can only be changed manually using the
main unit or Remote Control, or you can unplug and
re-plug the power adapter to cancel the previous
auto-synchronized time and repeat the Auto-Sync Clock
set up steps above.

Setting the Clock Time using the Remote Control

Wireless 1. Make sure the Docking Speaker is in Standby Mode, or
™
switch to Standby Mode by pressing and holding the
Button for 2 seconds until the Display Screen shows the
clock time.
2. Press and hold the CLOCK Button on the Remote Control
for about 2 seconds, until you see "24H" or "12H"
blinking on the LED Display Screen.
Press the ▲ and ▼ Button on the Remote Control to
3.
select a 12 or 24 Hour display format. Press the CLOCK
Button to confirm.
Press the ▲ and ▼ Button again to select the Hour time
4.
setting. The Hour digits will blink while you select the
correct Hour digit. Press the CLOCK Button to confirm.
When the Hour digit has been set, press the ▲ and ▼
5.
Button again to select the Minute setting. The Minute
digits will blink while you select the correct Minute digit.
Press the CLOCK Button to confirm.
LED Display
Screen:
Clock Time
Not Set
5