Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
NOTE: All of the information reported herein is based on data available at the time of printing. The factory reserves
the right to modify its own products at any time without notice or incurring in any sanction. Please verify with the
factory for possible updates.
1.
GENERAL SPECIFICATIONS
Quick Lift Model
Capacity
(kg)
Max. Fork Height
(mm)
Min. Fork Height
(mm)
Fork Length
(mm)
Width Overall Forks
(mm)
Individual Fork Width (mm)
Load Wheel Diameter (mm)
Steering Wheel Diameter (mm)
Net Weight
(kg)
Special fork length are available 800, 1000,1500, 2000mm.
Materials and specification are subject to change without notice.
2.
TO ATTACH HANDLE TO PUMP UNIT
2.1
Loosen the setting screw (324) on the crank link (325).
2.2
Remove three screws (D611) and three spring washers (D616) from the base (347).
2.3
Place the handle (610B, 610BA, 610B(JR), 610B(FR)) on the base (347), please note: Feed the rod and chain
(D612) through the centre of the base (347) and axle (346).
2.4
Insert three screws (D611) with spring washers (D616) into the base (347). Then tighten them securely.
2.5
Raise the crank link (325) and put the pin on rod and chain (D612) into the groove of crank link (325).
3.
TO ADJUST RELEASE DEVICE
On the handle of the pallet truck, you will find the control lever (D608) which can be set in three positions (See Fig. 1):
LOWER=to lower the forks; NEUTRAL=to move the load; ASCENT=to raise the forks. After assembling the handle, you
can adjust the three positions.
3.1
First tighten the setting screw (324) on the crank link (325) until the LOWER position function works.
3.2
If the forks elevate while pumping in the NEUTRAL position, turn the setting
screw (324) clockwise until pumping the handle does not raise the forks and
the NEUTRAL position functions correctly.
3.3
If the forks descend while pumping in the NEUTRAL position, turn the setting
screw (324) counter-clockwise until the forks do not lower.
3.4
If the forks do not descend when the control lever (D608) is in the LOWER position,
turn the setting screw (324) clockwise until raising the control lever (D608) lowers
the forks. Then check the NEUTRAL position as per item 3.2 and 3.3.
3.5
If the forks do not lift while pumping in the ASCENT position, turn the setting
screw (324) counter-clockwise until the forks elevate while pumping in the
ASCENT position. Then check the NEUTRAL and LOWER position as per item 3.2, 3.3 and 3.4.
4.
MAINTENANCE
OIL
Please check the oil level every six months. The oil capacity is about 0.3lt. Restore the fluid level in the rubber
reservoir to 5mm below the top, this must be with the forks in the lowered position.
Use the hydraulic type oil according to temperature scale below.
Temperature
-20℃~+40℃
4.2
HOW TO EXPEL AIR FROM THE PUMP UNIT
Air may enter the unit when the seals are replaced. Lift the control lever (D608) to the LOWER position, then move
the handle (610B, 610BA, 610B(JR), 610B(FR)) up and down for several times. It is also possible to pump up and lower
the pallet truck a few times, after that you have to lift up the rubber cap from the oil reservoir so that the air can
escape.
Oil
FINA HYDRAN TS22 Hydraulic oil
6
PT--
1000 - 2500
200
85
~
~
160
Ø 80
Ø 200
≥80-90
Werbung
Inhaltsverzeichnis
