Binding Process - Jamara Lamborghini Sian FKP 37 Gebrauchsanleitung

GB - Assembly
Attention: You do not need glue for this kit.
Please attach the stickers at the appropriate place before assembly.
1. / 1.1 Glue stickers 33, 34 and 35 on the part 46 as shown in the illustration. Attach part A3 to part 46 and parts B10 and C31 to part 46.
2. Glue sticker 29 on part B11. Fasten part C26 to part 46. Fasten part D36 and part D37 to part B11 as shown in the illustration.
3. Fasten part B11 to the front of part 46 as shown in the illustration.
4. Insert part D32 first at the bottom and then at the top into part B12. (See illustration)
5. Stick sticker 32 on part B14 Attach B12 to part 44 and part B14 to B9.
6. Stick sticker 30 on part C23 and sticker 31 on part C19. Attach part C23 to part C24. Insert the part that has just been assembled into the hole in part
B14 as shown. Fasten the parts C19 and B14 to part 44.
7. Glue sticker 13 on part C17. Plug part D35 onto part A5 and then part C30 onto part A5. Fix part C17 and part C16 together and attach now the part
as shown in the figure on part A5. Attach part C21 to part A5 as well. Fasten part D39 to part A5 as shown in the illustration.
8. Stick sticker 12 onto part C18 as shown in the illustration. Attach part D34 to part A4 and then part C29 to part A4. Attach part C18 and part C15 to
each other and attach now the part as shown in the figure on the part A4. Attach part C20 to part A4 as well. Fasten part D38 to part A4 as shown in
the illustration.
9. Apply stickers 18 and 19 as shown in the illustration. Place the assembled doors (parts A4 and A5) on the pins of part 44 and check that the doors are
open and can be closed. (See illustration)
10. Connect the two assembled parts together.
11. Fix part D33 on part C27. Fasten the assembled part C27 to part A7. Fasten part A7 to part 44 as shown in the illustration.
12. Fasten parts A1, A2 and A6 on the assembled model. (See illustration)
13. Fasten part A8 to part B13 and then the whole part to the previously assembled model as shown in the figure.
14. Insert 2 pins (55) left and right into the bottom of part 45. now insert 4 pins (56) into the corners of the bottom of part 45.
15. Attach parts 47 and 49 to part 45 as shown in the illustration.
16. Glue sticker 28 on part C25. Assemble the tires as shown in the illustration.
17. Connect part 47 and 48 and fix it on the model as shown in the illustration. Mount part 50 on the model. Connect the cables as shown in the figure.
18. Attach parts 52 and 53 to the model 45 as shown in the figure.
19. Connect cable 51 on the model. Pay attention to the length of both ends of the cable. The short end to the left and the long end to the right.
20. Fasten the loose cables in the gaps of the model. Connect the cables according to color and shape.
21. Attach parts 54 and C22 to the bottom of part 45.
22. Assemble the two assembled parts together. Insert 3x AA batteries into the model. By turning part C22 (lock) you can close the battery compartment.

Binding process:

Turn on the model. The light on the model flashes. Insert 2 AA batteries into the transmitter, the LED on the transmitter will flash.
When the LEDs on both the model and the transmitter stop flashing, they are bound.
Attention!
● Never operate your model beyond sight. Both the maximum visibility as well as the max. range of your model will depend on many factors such as
weather, location and interfering frequencies. Therefore, before each use perform a range test with a second person securely holding the model and
also check how the model reacts if there is a signal failure e.g. when empty transmitter batteries are installed.
11