Handling And Connection - Regent D-1000 Bedienungsanleitung

4. Handling and connection

Power
Plug the attached AC cord into a standard AC power outlet to power the DVD player.
Connecting Video and Audio
Note: Before making or changing any connections, make sure that all the devices are discon-
nected from the power outlet.
Note: Both video and audio connections must be made from the DVD Player to your televi-
sion.
RCA Stereo Audio Output:
1. Use the RCA Stereo Audio Output to send audio from the DVD player to a television.
2. Required an RCA audio cable (included).
3. Use the RCA audio cable to connect the RCA Stereo Audio Output to an RCA stereo
audio input on a television.
4. Adjust the connected televisions input setting to match the input used in the previous
step.
5.1 RCA audio output:
1. Use the 5.1 RCA audio connector to send the sound from the DVD to the TV.
2. RCA audio cable required (not included).
3. Use the RCA audio cable to connect the RCA 5.1 audio output to the RCA 5.1 audio input
on your HiFi equipment.
4. Adjust the connections in the input settings on the TV to those used in the previous
step.
Coaxial Digital Audio Output:
1. Use the Coaxial Digital Audio Output to send high quality audio from the DVD player to
an audio system.
2. Requires an RCA audio cable (included).
3. Use the RCA audio cable to connect the Coaxial Digital Audio Output to a coaxial digital
input on an audio system.
4. Adjust the connected audio system's input setting to match the input used in the pre-
vious step.
5. In the Digital Out portion of the setup menu, adjust to PCM, RAW or off.
Composite Video Output:
1. Use the Composite Video Output to send video from the DVD player to a television.
2. Requires an RCA video cable (included).
3. Use the RCA video cable to connect the Composite Video Output to a composite video
input on a television.
4. Adjust the connected televisions input setting to match the input used in the previous
step.
18
HDMI Output (Best):
Requires a HDMI cable (not Included)
1. Use a HDMI cable to connect the HDMI Output to a HDMI input on a television.
2. Adjust the connected televisions input setting to match the input used in the previous
step.
3. Set quality in the video settings.
SCART Output:
1. Requires a SCART cable (not included).
2. Use the SCART Output to send audio/video from the DVD player to a television.
3. Use the SCART cable to connect the SCART output in the DVD to a SCART input on a
television.
4. Press the Video button on the remote to switch to Scart mode.
S-Video Output:
1. Requires a S-Video cable (not included).
2. Use a S-Video cable to connect the S-Video Output to a S-Video input on a television.
3. Adjust the connected televisions input setting to match the input used in the previous
step.
4. Press the Video button on the remote to switch to S-Video mode.
Component Video Output:
1. Requires component video cable (not included).
2. Use a component video cable (not included) to connect the Component Video Output
on the DVD player to the Component Video Input on the television.
3. Adjust the television's source input setting to Component Video (YPbPr).
4. Press the Video button on the remote to switch to YUV mode.
DVD/CD
Loading a Disc
1. Press the Open/Close button to open the Disc Drawer.
2. Load a disc into the DVD player, label side facing up.
3. Press the Open/Close button to close the Disc Drawer.
4. After a disc is loaded, it will begin playing automatically.
SD Card / USB Disk/Stick
1. Plug the SD Card/USB drive into the port.
2. The supported formats should appear in the file browser.
3. Press DVD/USB/SD to switch the mode.
4. Use the navigation cross to navigate in the file browser.
EN
19