Cameo CLF1VMOUNTAP Bedienungsanleitung

USER MANUAL
CLF1VMOUNTAP
ADAPTER FOR MOUNTING STANDARD V-MOUNT BATTERIES ON CLF1 SPOTLIGHTS
INTRODUCTION
Operate a CL F1 spotlight independently of a mains connection using the optionally available
CLF1VMOUNTAP adapter and a standard V-mount battery.
INTENDED USE
The product is a device for event technology!
The product has been specially developed for professional use in the area of event technology and
is not suitable for use in a household setting!
Furthermore, this product is only intended for qualified users with expertise in event technology!
Use of the product contrary to the specified technical data and operating conditions is considered
improper!
Liability for damages or third-party damage to persons and property due to improper use is
excluded!
SAFETY INFORMATION
1. Please read this user manual carefully.
2. Keep all information and instructions in a safe place.
3. Follow the instructions.
4. Only use the V-mount adapter as properly intended.
KEEP AWAY FROM CHILDREN! THE PRODUCT CONTAINS SMALL PARTS AND
PACKAGING MATERIAL THAT COULD BE SWALLOWED! PLASTIC BAGS MUST BE KEPT OUT OF
THE REACH OF CHILDREN!
INSTALLATION
Fully disconnect the spotlight from the mains (pull out the mains plug).
Loosen and remove the four Allen screws, marked in the figure below, on the rear of the spotlight
using a suitable tool (A). Insert the four spacer sleeves attached to the V-mount adapter into the
corresponding screw holes (B) and screw the adapter into the rear of the spotlight using the
included screws (C).
Keep the original screws, which have been removed, for later reassembly.
Insert a fully-charged standard 14.4 or 14.8 volt V-mount battery into the adapter and connect the
connection cable to the 4-pin XLR socket of the spotlight (BATTERY).
The spotlight will now begin the start-up process and is operational after a short time.
A
PRODUCTNAME PRODUCTNAME
PROPER DISPOSAL OF THIS PRODUCT
Art No. XXX Art No. XXX
(Valid in the European Union and other European countries with waste separation)
PRODUCTNAME
Adam Hall assumes no responsibility or liability for the correctness, accuracy and completeness of this drawing. | Adam Hall übernimmt keine Gewähr oder Haftung für die Richtigkeit, Genauigkeit und Vollständigkeit dieser Zeichnung. Adam Hall assumes no responsibility or liability for the correctness, accuracy and completeness of this drawing. | Adam Hall übernimmt keine Gewähr oder Haftung für die Richtigkeit, Genauigkeit und Vollständigkeit dieser Zeichnung.
This symbol on the product or the associated documents indicates that the device must not be
Art No. XXX
disposed of with normal household waste at the end of the product's life, in order to prevent envi-
dam Hall assumes no responsibility or liability for the correctness, accuracy and completeness of this drawing. | Adam Hall übernimmt keine Gewähr oder Haftung für die Richtigkeit, Genauigkeit und Vollständigkeit dieser Zeichnung.
ronmental damage or personal injury caused by the uncontrolled disposal of waste. Please dispose
of this product separately from other waste and recycle it to promote sustainable economic cycles.
Private customers can contact the dealer from whom the product was purchased or the relevant
local authorities to obtain information on environmentally friendly waste management. Commercial
users can contact their supplier and check the contractually agreed terms and conditions on the
disposal of equipment. This product must not be disposed of with other commercial waste.
Subject to printing errors and mistakes, as well as technical or other changes!
B
PRODUCTNAME
Scale 1:5 Scale 1:5
05.06.2019 05.06.2019
Art No. XXX
V1 V1
Adam Hall assumes no responsibility or liability for the correctness, accuracy and completeness of this drawing. | Adam Hall übernimmt keine Gewähr oder Haftung für die Richtigkeit, Genauigkeit und Volls
Scale 1:5
05.06.2019
V1
Cameo
Adam Hall GmbH | Adam-Hall-Str. 1 | 61267 Neu Anspach | Germany
Phone: +49 6081 9419-0 | adamhall.com
Please note: if you connect the mains power supply to the spotlight during battery operation,
the spotlight will restart and it is only operational again after the start-up process (= operation
with mains power). The same applies if you disconnect the mains power supply from the spotlight
while a battery is connected (= battery operation).
Note: a connected battery is not supplied with charging voltage when the mains power supply is
connected at the same time.
Caution: to avoid damage to the spotlight, the plus and minus contacts of the connection cable
must not be interchanged!
BATTERY RUNTIME
With the F1T and F1D models and a battery with 100 Wh of electrical energy, the battery runtime
in Full On operation is calculated to be around 65 minutes.
With the F1FC model and a battery with 100 Wh of electrical energy, the battery runtime in Full On
operation is calculated to be around 45 minutes.
For batteries with a larger capacity, the runtime is extended accordingly.
The actual battery runtime depends on the ambient temperature and the technical characteristics
of the battery used (e.g. final discharge voltage).
TECHNICAL SPECIFICATIONS
Article number:
Product type:
Type:
Compatible spotlights:
Components:
Battery requirements:
Pin assignment of
connection cable
(4-pin XLR plug):
Color:
Material:
Dimensions of
mounting plate (W x H x D):
Total weight:
Scale 1:5
Cameo is a registered brand of the Adam Hall Group. Cameo
®
05.06.2019
Adam-Hall-Str. 1 · 61267 Neu-Anspach · Germany Adam-Hall-Str. 1 · 61267 Neu-Anspach · Germany
V1
DESIGNED AND ENGINEERED IN GERMANY. Assembled in PRC DESIGNED AND ENGINEERED IN GERMANY. Assembled in PRC
MANUFACTURER'S WARRANTY & LIMITATION OF LIABILITY
Our currently valid warranty conditions and limitation of liability are available at:
https://cdn-shop.adamhall.com/media/pdf/MANUFACTURERS-DECLARATIONS_CAMEO.pdf
For servicing, please contact Adam Hall GmbH, Adam-Hall-Str. 1, 61267 Neu Anspach
E-mail: Info@adamhall.com / +49 (0)6081 / 9419-0
® is a registered brand of the Adam Hall Group
CLF1VMOUNTAP
Spotlight accessory
Adapter for mounting standard V-mount
batteries on compatible spotlights
CL F1 Series
Mounting plate, battery adapter, connection cable, screw set
V-mount connection
14.4 or 14.8 volt nominal (min. 11 volt – max. 17 volt)
F1T / F1D: load capacity up to 10 A
F1FC: load capacity up to 15 A
pin 1 = negative (-)
pin 4 = positive (+)
Black
Metal / plastic
119.5 x 166.5 x 35.5 mm
0.29 kg
C
is a registered brand of the Adam Hall Group.
®
Cameo is a registered brand of the Adam Hall Group.
®
Adam-Hall-Str. 1 · 61267 Neu-Anspach · Germany
DESIGNED AND ENGINEERED IN GERMANY. Assembled in PRC
Cameo is a registered brand of th
®
Adam-Hall-Str. 1 · 61267 Neu-A
DESIGNED AND ENGINEERED IN