Werbung
ASSEMBLY INSTRUCTIONS
LONDON
PHOTOS 1 & 2. Go ahead with the correct identification of the parts and, to this end, number them as indicated on the PI sheet
that you will find on the last pages of this manual. Using a cutter separate the parts from the sheets by cutting the sprues. Then
use fine grain sandpaper to eliminate the rough edges and leave them ready to be painted, varnished or stained.
PHOTOS 3 & 4. Fit and glue the bench supports 2 onto the base 1. Use white glue. Fit and glue the fronts of the benches 3 and
the strips 4. Use white glue.
PHOTO 5. Glue the strips 5, starting from the strip 4 and until you have completely covered the benches. Sand them down well
and then varnish. Use white glue.
PHOTO 6. Stain the strips 6 and 7 sapelli colour and glue them to the front of the benches. Use white glue.
PHOTO 7. Take the strips 8, and glue the planking in place, leaving a 1 mm. gap between each strip. Use white glue.
PHOTO 8. After painting the planking light grey this is how the floor and the benches should look once assembled.
PHOTO 9. Separate parts 9, 10 and 11 from the sheet in order to make up the front of the coach.
PHOTO 10. Paint the doors 12 burgundy red on one side and then stain them sapelli colour on the other. Cut out the window
panes 13 and glue them into the doors.
PHOTOS 11 & 12. Paint the bevelled edges of the doors and the windows cream. Glue together the end pieces, with the doors
mounted between them but not glued in place. Use white glue. Paint the top outside of the panels burgundy red and the bottoms
cream. Glue the decorations 14 to the exterior of the panels.
PHOTOS 13 & 14. Glue the front-pieces to the body of the tramcar, making sure that the painted sides are facing outwards. Use
white glue. Fit the sides 15 and 16 and glue them into place to make up the central part of the lower saloon. Use white glue.
Varnish the interior.
PHOTO 15. Fit and glue the lower sides 17 into place. Use white glue. Sand down and fill the exterior on all of the sides.
PHOTO 16. Make a 1 mm diameter hole in the base of each support 18, so that eyebolts can be fitted into them, and then stain
them sapelli colour and glue them to the interior of the lower saloon. Use white glue.
PHOTOS 17 & 18. Glue the posters and signs 19 and 20 into place as shown in the photo. Use white glue. Glue the posters
and signs 21 and 22 into place as shown in the photo.
PHOTO 19. Adjust the length and fit an eyebolt 23 into each support 18.
PHOTO 20. Pass a length of the thread 24 through the eyebolts, allowing it to sag slightly between each support. Above this fit
and glue the bars 25 into place.
PHOTO 21. Paint the door knobs 27 gold and attach them to both sides of the doors. Glue the posters 28 and fit them in place
as shown.
PHOTO 22. Paint the lamps 28 gold and white, and then glue them in place on the sides of the lower saloon. Use cyanoacrylate
adhesive.
PHOTO 23. Stain the beams 29 of the roof sapelli colour and then glue them into place on the lower saloon supports. Use white
glue.
PHOTO 24. Glue the window panes 31 into the frames 30. Stain one of the sides sapelli colour. Glue the window frames into the
spaces set aside for them.
PHOTOS 25 & 26. Stain the window frames 32 sapelli colour and glue the window panes 33 into them, and then glue the
windows into the places set aside for them. Glue the advertisements 34 together and then fit them to the small windows at each
end. Use white glue.
PHOTO 27. Trim the window panes for the large windows on each side 35 and then glue them into place.
PHOTO 28. Glue the decorations 36 onto the roof beams. Use white glue.
PHOTO 29. Cut to size and glue the planking 38 in place on the platforms 37 leaving a separation of 1 mm between each strip.
Then paint them grey.
PHOTO 30. Paint the front part of the steps 39 black and then glue the finishes 41 onto them, along with the brackets 40.
PHOTO 31. Glue the steps 42, 43, 44, 45, 46, 47 and 48 onto the step fronts 39. Glue the sections of brass strip 49 onto the
steps.
PHOTO 32. Glue the first two steps onto the platforms, following the numerical order and making sure that they are perfectly
vertical.
Werbung
