Inhaltsverzeichnis
Werbung
WARNING: clean the grid after cooking in order to
IPX
avoid the formation of food and grease that could
catch fire. Cleaning the grid regularly ensures the pro-
per operation and safe use of the device.
Models :
SG9PL80M – G9PL40M – G9PL80M – PLG40B – PLG80B –
PLG40M – PLG80M – PLG40B/S – PLG80B/S – PLG40M/S
– PLG80M/S – G6PL60B – G6PL60M
Before using the device you must place the lava rock in its
holder, which is located between the burner and the grid,
taking care to distribute it uniformly. Use 7 kg of lava rock
for the single module and 14 kg for the double module.
WARNING: clean the burner regularly in order to remove
any powder from the lava rock or cooking residues.
The burners are supplied by a thermostatic safety valve.
The
G7WG40M
- G7WG80M/22S - SG7WG40M - SG7WG80M -
SG7WG40M/22S - SG7WG80M/22S - SG9WG40M -
SG9WG80M - LXG9WG40 - LXG9WG80 unit must never
work without water. Pour water up to 5/6 cm in each fat
collecting tray several time per day in order to facilita-
te cleaning and improve cooking.
Ignition of the pilot burner
Press down the knob and rotate it clockwise to the
(
) (PILOT). ) position.
In this position, keep the knob pressed down while
pushing the piezoelectric button several times until the pi-
lot flame ignites. Release the knob after 5 seconds. Repeat
the same operation if the pilot flame goes out.
Main burner ignition and temperature regulation
To turn on the main burners, rotate the thermostat knob
anticlockwise up to the desired temperature. To turn off
the main burner, rotate the knob right up to the position
(
).
To extinguish the pilot flame, move the knob to position (
Turning off in the event of a failure
In the event of a failure, cut off the gas supply to the
appliance.
What to do in case of malfunctioning or if the
appliance is not used for a long period of time
If the appliance is not to be used for a long period of time,
or in the event of a failure or malfunctioning, turn off the
external gas supply tap connecting to the main line. Call
for Technical Assistance.
Downloaded from
www.Manualslib.com
LXG9PL40 – LXG9PL80 –
SG9PL40M –
IGNITION
-
G7WG80M
-
G7WG40M/22S
TURNING OFF
manuals search engine
APPLIANCE CARE
ATTENTION!
- Before cleaning the unit, turn it off and let it cool
down.
Giving the appliance a thorough cleaning every day will
keep it in perfect working order and make it last longer.
All steel parts should be cleaned with a dish detergent
diluted in very hot water, using a soft cloth; to remove
stubborn dirt, use ethyl alcohol, varnish remover or another
non halogen solvent; do not use abrasive powder or
corroding detergents, such as hydrochloric/muriatic
or sulphuric acid. The use of acids can compromise the
functionality and safety of the appliance.
Do not use brushes, steel wool or abrasive pads made
with other metals or alloys that might leave traces of
rust. For the same reason, avoid touching the appliance
with anything made of iron. Pay attention to use steel
wool pads or stainless steel brushes that do not cause
rust but may cause damaging scratches. If the appliance
is extremely dirty, do not use emery or sandpaper. As an
alternative, we recommend using a synthetic sponge (for
example, the Scotchbrite sponge).
Do not use substances used to clean silver and pay
attention to hydrochloric or sulphuric acid that might
have been used to clean the floor.
WARNINGS FOR THE AUTHORIZED INSTALLER
ANOMALIES
Thermocouple:
The pilot flame does not remain on:
- Replace the thermocouple.
PIEZOELECTRICAL IGNITION
The spark is not visible:
Visually check the good condition of the piezo (it must not
be dirty with oil) and the small cable must not be cut or
stripped. Moreover, make sure that it is connected to the
frame by means of the cable and/or in contact with the
panel. If the piezo and the cable are in good condition,
replace the plug.
).
| 57
EN
Werbung
Inhaltsverzeichnis
