Safety Features; First Use; Taking The Appliance Out Of Service - Jupiter Variomaxx Gebrauchsanleitung

Operating Instructions Variomaxx
Timer function (90 - 0 min)
• Select a time using the + and - buttons.
• Leave the rotary knob at
• Start the timer by pressing the PAUSE/START button.
 The preset time is counted down on the LCD display.
• An alarm sounds when the time has elapsed.
• Clear the alarm by pressing the PAUSE/START button.
• You can stop the timer ( display flashes) and restart it
by pressing the PAUSE/START button.
• You can reset the preset time to
ously pressing the + and - buttons.
Stopwatch function (0 - 90 min)
• Leave the rotary knob at
• Start the stopwatch by pressing the PAUSE/START but-
ton.
 The time elapsed (0 - 90 min) is shown on the LCD
display.
• You can stop the stopwatch ( display flashes) and re-
start it by pressing the PAUSE/START button.
• You can reset the preset time to
ously pressing the + and - buttons.

Safety features

• The appliance cannot be started with the drive arm in
the raised position.
• If the drive arm is raised during processing, the appli-
ance stops.
 Reactivate the appliance when the drive arm is low-
ered again by pressing the PAUSE/START button.
• If there are too many ingredients in the bowl or the mix-
ture is too firm, the appliance will not start/processing
stops.
 The LCD display flashes.
 Remove some of the mixture from the bowl.
• The appliance stops automatically on overheating.
 One signal tone is sounded and the LCD display
flashes.
 Unplug the appliance, raise the drive arm and allow
the appliance to cool down for 30 min.
• After a processing time of approx. 20 min, the appliance
automatically switches into energy-saving mode.
 The appliance stops, two signal tones are sounded,
the display flashes for 5 s and is reset to
 Reactivate the appliance by pressing the PAUSE/
START button or activating the rotary knob.
• If it is not used, the appliance automatically switches
into energy-saving mode after approx. 20 minutes.
 The LCD display switches off.
 Reactivate the appliance by pressing the PAUSE/
START button or activating the rotary knob.
8 Subject to technical changes without notice; no responsibility is accepted for the accuracy of this information.
.
0
by simultane-
00:00
.
0
00:00 by simultane-
00:00 .

First use

• Ensure that the appliance's mains plug is plugged out.
• Before using the appliance for the first time, thoroughly
clean all parts of the appliance (see section
• Always ensure that the appliance is completely assem-
bled before operating it, with the mixing attachment
locked in place, with the bowl
and with the splash guard lid
• Place the appliance on a non-slip, even and clean sur-
face.
Switching on and setting the appliance
CAUTION Rotating parts can cause injury!
• Never put your hand into the appliance when the motor
is running.
• When the mains plug is plugged in, a short signal tone
is sounded, the LCD display lights red and the top line
flashes three times.

The appliance is ready to use.
1 Select a time (0 - 20 min) for processing by pressing the
+ and - buttons.
Turn the rotary knob to the desired speed level (
2
 Processing starts.
 The preset time is counted down on the LCD display.
• Once the time has elapsed, two signal tones are sound-
ed, the appliance switches off and the display flashes
.
00:00
Info:
• Alternatively, you can also start processing directly,
without preselecting the time, by setting the rotary knob
to a speed level.
• If you turn the rotary knob to position
ing, processing stops and the elapsed processing time
or the remaining time left of the preset time is set to
.
00:00
• You can change the speed level at any time.
• You can stop the currently running processing ( dis-
play flashes) and restart it by pressing the PAUSE/START
button.
Processing ingredients
See page 9
Using the mixing attachments

Taking the appliance out of service

• Set the rotary knob to
0
• Plug out the mains plug.
Cleaning
in position and locked
.
in position
0 - 12
during process-
0
.
.
).
).