Werbung
Verfügbare Sprachen
Verfügbare Sprachen
G Operating instructions
SAT Finder
Item no. 1378295
Intended use
The SAT Finder serves as an aid to set satellite antennas. Via the analog pointer instrument, you
can conclude the strength of the antenna signal and align the satellite antenna optimally to the
satellite. The function of the device is supported with an acoustic signal. One LED each shows
whether a 22 kHz signal is applied along with the selected polarisation level (vertical/horizontal).
The SAT Finder is only approved for connection to standard satellite components (SAT antenna,
receiver, multi-switch).
Contact with moisture must be avoided at all times. Any other use than the one described above
leads to damage to the product and is additionally tied to risks.
These operating instructions are part of this product. It contains important notices for commissi-
oning and handling. Please bear this in mind when passing on the product to a third party. For this
reason, keep these operating instructions for future reference.
This product complies with the applicable National and European requirements.
All names of companies and products are the trademarks of the respective owners. All rights
reserved.
Safety instructions and hazard warnings
D amage due to not following these operating instructions will void the warranty! We
do not assume any liability for any resulting damage!
W e do not assume any liability for material and personal damage caused by improper
use or non-compliance with the safety instructions. In such cases, the warranty will
be null and void.
• The unauthorised conversion and/or modification of the product is not allowed be-
cause of safety reasons.
• The product may not be subjected to extreme temperatures, strong vibrations, heavy
mechanical strain, direct sunlight or high degrees of humidity. This may damage the
product.
• The device is not a toy and should be kept out of the reach of children.
• Do not leave the packaging material lying around carelessly since it constitutes a
danger to children.
• Do not put the product into operation if it is damaged.
• The manufacturer or supplier will assume no responsibility for incorrect displays or
the consequences which arise through an incorrect display.
• Do not use the product in situations in which professional measuring technology is
required.
• Avoid using the device under unfavourable ambient conditions.
• The device may never be operated unsupervised.
• If questions arise which are not clarified in these operating instructions, please con-
tact our technical support or another specialist.
• In commercial institutions, the accident prevention regulations of the Employer's Li-
ability Insurance Associations for Electrical Systems and Operating Materials are to
be observed.
• Numerous regulations must be observed when installing/mounting satellite systems
(e.g. safety, lightning protection, etc.) Therefore, a satellite system should always
be installed and serviced by a technician familiar with the corresponding risks and
regulations.
• The installation and servicing of satellite systems also requires knowledge of the ac-
cident prevention regulations. When installing or servicing satellite systems, ensure
a safe stand and sufficient weight-bearing capacity of ladders and similar equipment
(have this secured by a second person, if applicable). When working on satellite
systems, wear slip-proof shoes and suitable clothing. It may be necessary to secure
the installation site (e.g. wear safety belts). In the interests of your own safety, you
must always comply with the safety instructions.
• Also observe the safety and operating instructions of any other devices that are con-
nected to this device.
Control elements
1) Connection „TO-LNB" Connection for the LNB
2) 22 kHz display Display of the 22 kHz conversion signal
3) H/V display Display of the polarisation level
4) Analog pointer instrument Signal strength indicator
5) Adjuster Controller for dampening the input signal
(6) "TO-REC" socket Connection for the satellite receiver
Connection of the SAT finder and alignment of the satellite antenna
To prevent short circuits, separate any multi-switches and the satellite receiver from
their power supply before connecting (pull the power plug). Avoid short-circuiting or
overloading the connected F connection cable or the SAT Finder connection "To-LNB",
otherwise the SAT Finder or the connected receiver may be damaged.
Do not position the SAT Finder directly in front of the satellite dish, otherwise the display
will show full power at all times.
A jump of the display to the highest value of the display scale means that the receiver
signal is too high for the SAT Finder. In this case, reduce the sensitivity of the SAT Finder
by turning the control knob counter-clockwise. If this is not enough to receive a medium
display range, e.g. when using a high-capacity LNB with high amplification (>60 dB) or
a satellite antenna that is larger than 1 m, you should insert an additional level control-
ler between the LNB and the SAT Finder (attenuation controller 0 - 20 dB).
• Connect the output of the LNB with the connection "TO-LNB" of the SAT Finder (lettering on the
back). For this purpose, use a short coaxial cable with an F-plug on both ends.
• Connect the connection "TO-REC" of the SAT Finder with the antenna input of the satellite re-
ceiver (often marked with "IF INPUT").
• Check the correct connection. Plug the mains plug of the SAT receiver into a wall outlet and turn
the receiver on.
• The satellite finder is supplied with power via the connected SAT receiver. Now the display of
the SAT Finder should be illuminated.
• Roughly direct the satellite antenna towards the desired satellite. Inform yourself about the
correct value for the height and side angle required for adjusting in the instruction manual of the
satellite antenna, the Internet or professional literature.
• Turn the adjustment control on the front of the SAT Finder until the pointer of the display inst-
rument shows "5". The display is supported with an acoustic signal. The higher the signal, the
better the antenna is aligned towards the satellite.
• Change the position (height and side angle) of the satellite antenna until the pointer shows ma-
ximum.
• When the pointer shows the top value, turn the adjustment controller counter-clockwise until
the pointer is roughly in the center of the display scale. It may be necessary to repeat this pro-
cess several times while adjusting the satellite antenna.
• By finely adjusting the satellite antenna, try to achieve a high pointer and acoustic signal.
• Once the satellite antenna is optimally set, fix it in place (observe the manufacturer's instruc-
tions).
• Pull the mains plug of the satellite receiver and remove the SAT Finder from the antenna path.
• Connect the LNB with the satellite receiver or restore the original cabling. Check the picture on
the TV and whether the right satellite is accessed. You may have to repeat the setup procedure.
Checking the polarisation levels:
The H/V display indicates the polarisation level selected by the SAT receiver. With a vertical pola-
risation level, the LED does not light up, with a horizontal polarisation level it lights up. To be able to
align the satellite antenna optimally on both polarisation levels, you should switch the polarisation
level when adjusting the satellite antenna.
Checking the 22 kHz conversion signal:
The 22 kHz display lights up as soon as a 22 kHz signal is received. The 22 kHz signal is generally
used to switch an LNB from the bottom (analog) frequency band to the top (digital) frequency band.
Maintenance, cleaning and servicing
The SAT Finder is maintenance-free, therefore you must never open it. If you do open it, the war-
ranty will be rendered null and void. The outside of the device should be cleaned with a clean
dry cloth or brush only. Do not use abrasive cleaning agents or chemical solutions which could
damage the housing or the display or impair operation.
Disposal
Electronic devices are recyclable waste materials and must not be disposed of in the
household waste!
Please dispose of the product, when it is no longer of use, according to the current
statutory requirements.
Technical data
Operating voltage............................... 13 - 18 V/DC (supply via the satellite receiver)
Current consumption ......................... approx. 100 mA
Frequency range ................................ 950 - 2400 MHz
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.
Werbung
