Laica HYDROSMART Anleitungen Und Garantie Seite 7

EN GENOVA tap filter
6) To install the connector with the M adapter, proceed as follows:
Remove the fastening ring from the connector and take the adapter L with diameter Ø 21 mm complete with seal
-
N, then assemble the three pieces as described in figure 6A, 6B, 6C.
6A
- Loosen the fastening band with a flat head screwdriver and remove the two rubber seals inside the adapter M
(fig. 7a, 7b).
7A
Choose the best seal: only the one with the biggest diameter (Fig. 8A) or both with one inserted inside the other
-
(fig. 8C). Then, insert them in the adapter, pressing firmly and taking extra care over which way up they are
inserted (fig. 8D).
8A 8B
- Install the adapter M on the tap and tighten the fastening band using a flat
head screwdriver to secure it firmly to the tap (fig. 9A and B).
9A 9B
7) Remove the HYDROSMART™ filter from its packaging and rinse it under running water. Now hook the filter to
the connector as shown in figure 11A, 11B, 11C.
11A 11B
6B 6C
7B
8C 8D
- Screw the connector onto
the ring (fig. 10).
10
11C
12
Instructions and guarantee
SMART FILTRATION SYSTEM – FREE LAICA HOME
WELLNESS APP - USE
List of compatible devices:
• iOS: iPhone with version 10 operating system.
• For devices with Android™ operating system:
from version 6.0 (Marshmallow).
By adding the HYDROSMART™ filter to the free "Laica
Home Wellness" app, you can receive automatic
notification on your smartphone when to replace the filter.
1. Install the free "Laica Home Wellness" app on your
smartphone.
2. Start the app and enter the "FILTER" section from the
main screen.
3. Add the HYDROSMART™ FILTER by pressing the
"+" key. It is possible to add the filter by scanning
the QR code printed on the upper part of the filter or
manually by pressing the "Select manually" button.4.
The app adds the filter and automatically prompts the
replacement date.
To optimise the effective duration of the filter based
on the water treated, you can select the chlorine level
in your water supply.
To use it properly, request further information from your
water supplier or carry out a preliminary assessment
of the local water supply.
5. Save the settings by pressing the " " key.
6. When the filter replacement date is reached,
the notification to replace it will appear on your
smartphone. The notification is also sent to the email
address given during registration.
• To scan the QR code on the upper part of the
filter, you must authorise the app to access
to your smartphone camera.
• To receive notifications when to replace the
filter, you must enable the settings on your
smartphone.
• To replace the filter, you can add a new one
by scanning the QR code printed on the
upper part of the filter or by updating the
expiry date by clicking on the "Filter expired"
button (click to replace)".
USING THE FILTERING SYSTEM
Activating the Laica HYDROSMART™ filter:
When first used and every time the HYDROSMART™
filter is changed, turn the tap on and allow the water to
flow through the filter for several minutes (at least 4-5
minutes) to correctly activate the materials of which the
filter is composed. This water can be used for watering
plants. If the Laica filtering system has not been used
for 24 hours or more, allow the water to flow for 30-60
seconds before using the filtered water again.
CAUTION:
- To guarantee the performance characteristics of the
filtering system, it is recommended to filter cold water
only.
- The flow of water at a temperature higher than 50°C
through the connector may cause permanent damage.
The flow of water at a temperature higher than 35°C
through the filter may cause permanent damage.
- To adjust the water flow properly, open the tap slowly.
The Laica filtering system has 2 different ways of
dispensing the water which can be selected with the
selector C:
1) Filtered water for
drinking, washing
fruit and vegetables,
cooking and carry out
all routine tasks with
safe, pleasant tasting
water.
2) Unfiltered water with
spray head.
REPLACING THE FILTER
To replace the filter, turn the filter anticlockwise and
remove it by pulling it outwards (fig. 12A, 12B, 12C).
12A 12B
12C
Replace it with a new filter repeating the steps described
in point 7 of the paragraph "PREPARING THE FILTERING
SYSTEM" and "USING THE FILTERING SYSTEM - Activating
the Laica HYDROSMART™ filter".
To achieve the best results and guarantee the safety of
the filtering system, we recommend replacing the filter
every 3 months or 900 litres of filtered water.
CARE AND MAINTENANCE
Make sure your hands are clean during maintenance work
on the filtering system.
Regularly clean the outer part of the connector with
a damp sponge and delicate detergent, then rinse
thoroughly with cold drinking water.
Do not use aggressive detergents, solvents, chemical or
abrasive products.
It is recommended to thoroughly clean the entire
connector each time the filter is changed.
For maintenance, remove the entire filtering system by
following the installation instructions in reverse order.
1) Rinse the connector under unfiltered running drinking
water.
Do not use detergents, solvents, chemical or abrasive
products to clean the connector.
If necessary, remove the fastening ring (E), the rubber
seal (F) and rinse the stainless steel strainer (G) under
13
EN