Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating instructions
Multi-card reader small
Item no. 1095088
Intended use
The product is intended for reading and writing to compatible memory cards. It is
designed for a personal computer (PC) with USB 2.0 connection and is backward
compatible with USB 1.1.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in
bathrooms, must be avoided under all circumstances.
For safety and approval purposes (CE), you must not rebuild and / or modify this
product. If you use the product for purposes other than those described above, the
product may be damaged. In addition, improper use can cause hazards such as short
circuiting, fire, electric shock etc. Read the instructions carefully and keep them. Make
this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All
company names and product names are trademarks of their respective owners. All
rights reserved.
Delivery content
• Card reader
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong
jolts, high humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can no
longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a
low height can damage the product.
• Also observe the safety and operating instructions of any other devices
which are connected to the product.
• Consult an expert when in doubt about operation, safety or connection of
the device.
• Maintenance, modifications and repairs are to be performed exclusively
by an expert or at a qualified shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Operation
• Switch your computer on and wait until the operating system has completely booted
up.
• Plug the USB plug into an available USB port on your computer.
• Insert the memory card(s) into the corresponding slot with the correct orientation.
Look at the illustration printed on the housing of the card reader.
The card reader or the card may be damaged if the card is not inserted in the
correct orientation.
The MS / MSPRO and the M2 slots cannot be used at the same time. Use
only one of them at a time. The same applies to SD and micro SD as well.
• A new drive / drives will appear on your computer. Follow the operating instructions
for your operating system to read and write to the card(s).
Some memory card formats (such as exFAT) may require the installation of
a system patch before the card reader can recognize the memory card. For
more information, refer to the operating instructions and the latest update
information for your operating system.
• Before removing the memory card(s), perform the necessary operations to ensure it
is safe to remove the card(s). Refer to the operating instructions for your operating
system.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste.
At the end of its service life, dispose of the product according to the
relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the
environment.
Technical data
Suitable for: ..........................................SDXC / SDHC / SD / MS / M2 / Micro SD / MMC /
System requirements .........................Windows® 2000, ME, XP, 7 (32 / 64 bits),
Operating voltage................................5 V/DC (via USB)
Current consumption ..........................max. 500 mA
Transmission rate ................................max. 480 Mbps
Operating temperature.......................0 to +40 ºC
Operating humidity..............................20 – 80 % RH
Storage temperature ..........................0 to +40 ºC
Storage humidity .................................20 – 80 % RH
Dimensions (W x H x D)......................105 x 18 x 23 mm
Weight ...................................................31 g
These operating instructions are published by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2014 by Conrad Electronic SE.
CF I / CF II / MD / XD
Windows® Vista™ (32 / 64 bits)
V1_0314_02-HK
Werbung
