Werbung
Verfügbare Sprachen
Verfügbare Sprachen
O P E R A T I N G I N S T R U C T I O N S
www.conrad.com
Floor Lamp
Item-No. 57 26 87
Intended Use
The floor lamp is intended for room illumination. The product is intended for placement and use
in dry indoor rooms, it must not get damp or wet.
Any use, other than that described above, could lead to damage to this product and involves the
risk of short circuits, fire, electric shock, etc.
No part of the product should be modified or reassembled. Never dismantle the product (except
to replace the light source, if necessary).
All the safety and assembly instructions must be carefully followed!
This product complies with the applicable National and European specifications.
Included in the Delivery
• Floor lamp with light source
• Base with assembly material
• Operating Instructions
Safety Instructions
The warranty will be void for damage arising from non-compliance with these
operating instructions. We do not assume any liability for any consequential
damage!
We do not assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions. The warranty is
voided in such case!
• For safety and approval (CE) reasons, unauthorised conversion and/or modifica-
tions to the product are not permitted. Never take the product apart (except to
change the light source, as described in these operating instructions).
• The product design complies with safety class I. Only power the lamp via a nor-
mal power socket (230V~/50Hz), with protective earth, connected to the mains
power supply.
• The product is only intended to be placed and used in dry indoor rooms, it must
not get damp or wet.
ï
The floor lamp must not be installed and used in a bathroom or near a shower,
swimming pool etc.
ï
Danger to life due to electric shock!
• Do not allow children to play with the device. Children cannot assess the dangers
arising from incorrect use of electrical devices. Therefore, be especially careful
when children are around.
• There is a risk of injury if the product topples over, due to its mass and design,
furthermore, other objects/furniture may be damaged.
ï
Place the cable so that nobody can trip over it.
• Do not look directly or indirectly into the light, this can cause eye damage.
• Before replacing the fluorescent light, switch off the floor lamp and disconnect the
plug from the mains socket. It is not sufficient just to switch off the lamp!
ï
Only operate the floor lamp with the cover closed; re-insert the cover correctly
after replacing the light source.
• Do not leave packing materials unattended. They may become dangerous play-
ing material for children.
• Handle the product with care, it can be damaged by impact, blows, or if it tips over.
• The product must not be used any longer if it is damaged, remove the plug from
the socket.
ï
A defective mains cable should only be replaced by a specialist!
• You should also heed the additional safety instructions in each chapter of this
manual.
• If you have any questions that are not answered in this instruction manual, please
contact our technical support centre or consult a professional.
Assembly
The delivered base is to be fixed at the bottom side with two screws
(each with a chopper disc). Tighten the screws firmly (do not use force).
Version 07/08
°
Placement
The product is only intended to be placed and used in dry indoor rooms, it must not
get damp or wet.
The floor lamp must not be installed and used in a bathroom or near a shower,
swimming pool etc.
Danger to life due to electric shock!
The floor lamp must be placed on an even, firm, horizontal and sufficiently large surface, other-
wise the floor lamp may tip over.
Place the cable so that nobody can trip over it.
Start-up
Plug the mains plug into a mains socket (230V~/50Hz) after installation.
The on-/off- switch of the lamp (with integrated dimmer) is located on the top.
Turning the switch clockwise switches on the lamp and the light intensity increases. To reduce
the intensity, turn the switch anti-clockwise. Keep on turning the switch anti-clockwise until a click
is heard, the lamp is switched off.
Replacing the Light Source
The lifetime of fluorescent lamps is normally longer than that of normal light bulbs. However, it
has to be considered that switching the fluorescent light on and off frequently can reduce its life-
time considerably.
Proceed as follows to replace the light source:
First, disconnect the floor lamp from the mains voltage, pull the plug out of the
mains socket!
• Remove the transparent plastic
cover.
To do this, insert a flat screw-driver
between the housing and cover
and carefully pry out the cover.
Do not use force, since the cover
and the lamp housing will be
damaged.
• Release the light source by turning
it 90° to the right or to the left.
Afterwards, you can remove it
carefully.
Protective caps attached to the
ends of the fluorescent tube only
serve visual purposes (to cover the
ends of the tube).
Do not use force when pulling out
the fluorescent tube, otherwise it
can break.
• Afterwards, insert a new light (T5, max. 54W), proceed in
reverse order.
If there were protective caps on your floor lamp's light (may
not be present in your version of the floor lamp), attach them
to the new fluorescent tube correctly.
Insert the light completely into the light fitting, top and bottom,
and lock the fluorescent tube in place by turning it 90° either
to the left or to the right.
Do not use force when turning, otherwise the light may be
damaged!
Finally, the cover has to be replaced so that it snaps in place.
Only use the floor lamp with the cover fully closed!
• The floor lamp can now be connected with the mains and put into operation.
Handling
• The floor lamp is only designed for use in dry indoor rooms, it must not get damp or wet, lethal
danger of an electric shock! Follow the safety instructions and the other information in this
operation manual.
• Never look directly into the light, when it is lit, as this can (just as with other lights) cause eye
damage!
• Ensure that the insulation for the entire product is neither damaged nor destroyed. Do not open
or dismantle the housing (except when it is necessary to replace the light source, see above).
• Check the product for damage before use! If you notice any damage, do not use the floor lamp
any longer, disconnect it from the mains, pull the plug out of the mains socket.
Any maintenance or repair work must only be carried out by authorised personnel.
Safe operation must be presumed to be no longer possible:
- if the device is visibly damaged
- if the device no longer works
- if the device was stored under unfavourable conditions for a long period of time or
- if it was exposed to extraordinary stress caused by transport
Maintenance and Care
Apart from occasionally cleaning the product and changing the fluorescent tube, it is mainte-
nance-free.
Clean the product with a soft, clean and dry cloth. Never use aggressive cleaning agents or
chemical solutions, these affect the surface of the housing (e.g. discolouring).
Disposal
Please dispose of the device when it is no longer of use, according to the current
statutory requirements.
The fluorescent light is special waste and has to be disposed of accordingly! It must
not be disposed of in the domestic waste!
Technical Data
Operating voltage: ................................230V~/50Hz
Type of light source: ............................T5, max. 54W
Base dimensions: ................................Ca. 25 x 18cm
Total height (incl. base): ......................ca. 174cm
1
2
Weight: ................................................ca. 5.2kg
Dimensions and weight can differ due to allowed manufacturing tolerances.
3
4
5
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
The operating instructions reflect the current technical specifications at time of
print. We reserve the right to change the technical or physical specifications.
© Copyright 2008 by Conrad Electronic SE. Printed in Germany.
Werbung
