Profile Sirocco Handbuch Seite 13

ELECTRIC CONVECTOR HEATER
282000110 Sirocco
We thank you for the purchase of this Profile product.
Caution: It is important that you read this manual before
using the product Then keep this manual in a safe place.
Technical information
 Mains voltage: 220V – 240V AC (50/60Hz)
 Power: - In position 0  OFF
- In position 1  750W
- In position 2  1250W
- In position 3  2000W
 IPX0 (no protection against water)
 Protection against overheating
 Adjustable built-in thermostat
 Ideal for usage in dry areas up to a maximum of 25m²
Connection
The heater is supplied with a plug. Never use the
appliance with a damaged cable and/or plug, after the
heater has not been working properly, or if it has been
damaged in whatever way.
The replacement of a cable and/or socket plug may only
be done by a qualified professional who is familiar with
the applicable requirements.
Installation
 Carefully turn the radiator on its side to assemble the
feet.
 Fit each foot (fig. 1) and tighten them with the screws
supplied.
 Two screws are needed for each foot. Do not use the
radiator if the feet are not properly assembled!
Fig. 1
Operation and functions
Operation:
 Switch the power switches to position 0.
 Insert the plug in the socket.
 Press the switch(es) with the required wattage
to switch the radiator on.
Use:
 The thermostat will automatically maintain your desired
room temperature.
 Switch on one or a number of switches depending on
the speed at which you want to obtain the desired
temperature.
Switch 1: 750W
o
Switch 2: 1250W
o
Switches 1 and 2: 2000W
o
 Turn the thermostat clockwise until you hear a click.
This sound means that the heater is now switched
on.
 If the indicator light is on the heater is working.
 Turning the thermostat clockwise increases the
temperature set. Conversely, turning it anticlockwise
lowers the temperature set.
 The thermostat automatically switches the heating
on and off when the set temperature has been
reached.
Note
 Allow the radiator to fully cool down before moving it
and always use the handle for this purpose.
 Protection against overheating: if this is activated the
radiator switches itself off. Then switch the radiator
off and pull the plug from the wall socket. Allow it to
cool down and remove any hindrances before using
the radiator again.
Cleaning
 We advise you to carefully clean the heater once a
month to remove dirt and dust. This ensures the
heater will continue working efficiently and safely.
 Always switch the thermostat off and remove the
plug from the socket. Make sure the appliance has
fully cooled before cleaning.
 Clean the housing with a clean, soft and lightly
moistened cloth. Never clean the heating elements
or thermostat in water. Blow as much dust as
possible off the heating elements. This extends the
life of the appliance and eliminates fire risks.
 Let everything dry thoroughly before switching the
heater on again. Do not use any detergent, wax or
cleaning agents; these can react under the influence
of heat and cause the colour to deteriorate.
 Save the box for storage during periods you are not
using the ceramic heater. When being stored the
heater must also be protected against dirt and dust.
Guarantee
The guarantee period amounts to 2 years and
commences on the date of purchase. During the
guarantee period Eltra NV resolves any defects
caused by material or manufacturing faults. Eltra NV
may choose to either repair or replace a defective
appliance.
Eltra NV is not obligated to repair or replace units if the
defect is a result of damage, misuse, modification or
changes made after the date of purchase.
Bring the defective device, along with the original sales
receipt, back to the shop where the unit was
purchased. Always include a note describing the
problem.
EN - 1