Reverse Switch - Gemini PS-525 PRO Bedienungsanleitung

uggest that you carefully read all the instructions.
To reduce the risk of electrical shock, do not open the unit. There are
NO USER REPLACEABLE PARTS INSIDE. Please refer servicing to a
In the U.S.A., if you have any Problems with this uni
D
O
radiator or Stove.
This unit should be cleaned only with a damp cloth. Avoid solvents or
other cleaning detergents.
When moving this equipment, it should be placed in its original carton
and packaging. This will reduce the risk of darnage during transit.
DO NOT EXPOSETHIS UNITTO RAIN OR MOISTURE.
DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY
CONTROLS OR SWITCHES.
Before plugging in the power cord, make sure that the VOLTAGE
SELECTOR (27) switch is set to the correct voltage.
Make sure that the POWER (21) switch is in the off Position.
The PS-525 PRO is supplied with 3 sets of amp output jacks. The
MASTER OUTPUT (28) jacks are unbalanced and used to connect to
your main amplifier. The OUTPUT REC (30) jacks tan be used to
connect the mixer to the record input of your recorder enabling you to
an additional amplifier.
The DJ MIC (1) input (found on the front Panel) accepts a 114"
connector and balanced and unbalanced microphones.
stereo LINE (32,34) inputs. The PHONONLINE SWITCHES (36,37)
enable you to set the (33, 35) inputs to Phono or Line. The phono
Downloaded from www.Manualslib.com manuals search engine
GROUND SCREW (38) for you to ground your turntables is located on
such as a CD player, a cassette player, etc.
6. Headphones tan be plugged into the front Panel mounted HEADPHONE
(22) jack.
Depending on your System configuration, sometimes applying the ground
will create a quieter Signal path. Sometimes lifting the ground tan eliminate
ground loops and hum to create a quieter Signal path.
1. With the mixer on, listen to the System in idle mode (no Signal present)
with the ground applied (the GROUND LIFT SWITCH (31) in the left
Position).
2. Then turn the power off before moving the GROUND LIFT
SWITCH (31). Lift the ground by moving the GROUND LIFT SWITCH to
the right, turn the power back on and listen to detenine which
Keep the GROUND LIFT SWITCH in the ground Position if the noise
CAUTION: DO NOT TERMINATE THE AC GROUND ON THE POWER MIXER
IN ANY WAY. TERMINATION OF THE AC GROUND CAN BE HAZ4RDOUS.
POWER ON: Once you have made all the equipment connections to
your mixer, press the POWER SWITCH (21).
CHANNEL 1: The GAIN (8), HIGH (9), MID (lO), and LOW (11) controls
CHANNEL SLIDE (13) controls the output level of this channel.
CHANNEL 2: The GAIN (8), HIGH (9), MID (IO), and LOW (11) controls
to select either the PHON0 21LINE 3 (33) or the LINE 4 (32) input. The
CHANNEL SLIDE (20) controls the output level of this channel.
SUGGESTION: You tan use the Cut Features on each channel to
remove Low, Mid and/or High to create special effects.
4. CROSSFADER SECTION: The CROSSFADER (18) allows the mixing of
one Source into another. The left side of the CROSSFADER (18) is
CHANNEL 1 and the right side is CHANNEL 2. The CROSSFADER
REVERSE SWITCH (17) allows you to reverse the crossfader so that
CHANNEL 2 is controlled by the left side of the crossfader and
CHANNEL 1 is controlled by the right side of the crossfader.
The CROSSFADER (18) in your unit is removable and if the need
varieties. Part # RF-45 (which is identical to the crossfader supplied
with the mixer) has a 45 mm travel from side to side. Part # RF-30 is
available with a 30 mm travel distance. Also available is the PSF-45
with a special curve designed for scratch mixing. Just purchase one
of these crossfader units from your Gemini dealer and follow these
instructions:
Page 3